Installing ProStart CT-3300

Home / the12volt's Install Bay / Car Security and Convenience / Installing ProStart CT-3300 (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

whoever

Member - Posts: 1

Joined: January 09, 2005

Location: Canada

Posted: January 10, 2005 at 11:30 AM / IP Logged

I'm trying to install a ProStart CT-3300 in a 1992 Toyota Camry, but can't figure out which wires to connect for the lock/unlock feature. The wiring connections chart which I downloaded from Prostart/Autostart doesn' seem right because I can't find the light green or light green and blue wires that are supposed to be in the blue connector behind the driver's kick panel. Same goes for the lock/unlock wires indicated in the chart which I got from Vehicle information database here. If anyone knows for sure which wires need to be connected and where they are located, I'd really appreciate a response because this is a Christmas present for my wife and my reputation as a hanyman is at stake.

Falcon 1

Copper - Posts: 130

Joined: November 15, 2003

Location: Canada

Posted: January 10, 2005 at 12:56 PM / IP Logged

Here is some info.

Current Vehicle:

1992 Toyota Camry

Item	Wire Color	Polarity	Wire Location
12V	white - WHITE/ red	+	ignition harness
STARTER	BLACK/ white	+	ignition harness
IGNITION	BLACK / YELLOW	+	ignition harness
ACCESSORY	pink/blue *1	+	ignition harness
SECOND ACCESSORY	BLACK/ orange	+	ignition harness
TACHOMETER	black		check connector *2
POWER LOCK	blue/white	-	passengers kick blue plug
POWER UNLOCK	lt. GREEN/ red	-	passengers kick blue plug
PARKING LIGHTS +	green		bottom of fuse box *3
PARKING LIGHTS -	green		steering column
DOOR TRIGGER	RED / white	-	*4
HEADLIGHTS	RED / yellow	-	steering column
WIPERS
LF WINDOW UP/DN	green - red	A	drivers door switch
RF WINDOW UP/DN	grn/wht - RED / blu	A	drivers kick panel
LR WINDOW UP/DN	grn/yel - RED / blk	A	drivers kick panel
RR WINDOW UP/DN	grn/blk - RED / blk	A	drivers kick panel
TRUNK/HATCH PIN	RED / white	-	light or sw. in trunk
HOOD PIN
TRUNK/HATCH RELEASE
FACTORY ALARM ARM
FACTORY ALARM DISARM
HORN TRIGGER	GREEN/ black	-	steering column
BRAKE WIRE	GREEN / WHITE	+	bottom of fuse box *3
LOCK MOTOR	none	non	none
UNLOCK MOTOR	none	non	none
DISARM DEFEAT	none	non	none
DISARM NO UNLOCK	none	non	none
DOME SUPERVISION	none	non	none
SPEED SENSE	none	non	none
SUN ROOF OPEN/CLOSE	none	non	none
SUN ROOF LIMIT	none	non	none
LF SPEAKER	none	non	none
RF SPEAKER	none	non	none
LR SPEAKER	none	non	none
RR SPEAKER	none	non	none
RADIO 12V	none	non	none
RADIO GROUND	none	non	none
RADIO SWITCH	none	non	none
RADIO ILLUMINATE	none	non	none
POWER ANTENNA	none	non	none

Notes:	1 Not required for remote start. 2 Located on the rear side of the passenger strut tower. 3 In a white connector just below the fuses with the wires exiting out toward you. 4 Remove black plastic air duct covering the top right side of the fuse box to access a 6 pin plug containing the RED / white.

Do it right the first time, only a doctor can bury his mistakes.

Craig3708

Copper - Posts: 155

Joined: January 30, 2004

Location: Canada

Posted: January 10, 2005 at 3:58 PM / IP Logged

This car has child saftey locks. The lock wire from module goes directly to the Light Green in drivers kick panel and the unlock wire goes to two wires. The Dark green wire and the Child Safety Locks BLUE/RED in the drivers kick panel. Diode each one of these unlock wires to make it all work.

Craig.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Installing ProStart CT-3300

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.