the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Viper 791 XV, 98 Nissan 240sx


Post ReplyPost New Topic
< Prev Topic Next Topic >
black pearl 
Member - Posts: 7
Member spacespace
Joined: December 30, 2005
Location: United States
Posted: January 21, 2006 at 7:28 PM / IP Logged  

Hi all! Looking forward to doing the Viper 791xv install on my 98 240sx, no factory alarm or keyless entry, but power locks/windows.  I'm almost there just that there are a couple wires I'm not so sure of and I am hoping someone can help me out.  Please correct me if I am wrong on the following:                                                                                            the H1/6 BLUE wire(-) connects directly to the RED wire of the trunk pin, so if trunk is opened when system is armed it triggers alarm right?                                                                                                                                                        I'm also confused on where to connect the H1/3 WHT/BLUE (-) remote start activation input (i know it has to make ground but how do i connect?)

I'm looking to install a 530T window system, the only wire I can't figure where to connect to is the H2/5 GRAY(-) output during activitation wire, I know there is a relay involved just don't know how to connect it properly, I wouldn't want to trigger the alarm when rolling down, up, or venting , the windows.

For climate controls of remote starter the connections to a relay are as follows:                                                                 85 and 87 +12 volts 30amps fused,                                                                                                                                            87a white acc wire key side of vehicle,                                                                                                                                         30 ORANGE heavy guage wire from unit and white acc wire from vehicle dash side,                                                          86 connects to PINK (-) 200mA 3rd ignition output wire on the thin 4 wire relay satallite ribbon harness, is this right?if not can someone please correct me. 

And finally, the 2nd starter wire is connected to a relay as follows.                                                                                        86 connects to the thin VIOLET (-) 200mA starter output wire on the thin 4 wire relay satallite ribbon harness,          30 connects to the BLACK/ white 2nd starter wire on the vehicle,                                                                                               85 and 87 are connected to +12V 30amps fused, right?

I'am sorry for all the questions, but I do appreciate all the potential help and feedback, thanks in advance!

black pearl 
Member - Posts: 7
Member spacespace
Joined: December 30, 2005
Location: United States
Posted: January 22, 2006 at 9:56 PM / IP Logged  
A little help please. Someone, anyone.... please.
redpeppers 
Silver - Posts: 483
Silver spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: May 24, 2005
Location: United States
Posted: January 23, 2006 at 12:55 AM / IP Logged  
I'm also confused on where to connect the H1/3 WHT/BLUE (-) remote start activation input.......not used.....that wire activates the remote start , for example if u have a separte alarm or something, In ur case it wll not be used.  You are correct about the blue wire.....the remote start will come with a remote start relay pack that will have a high current starter, ignition, 2nd ignition, and accessory wire coming off of it which u can wire directly to the wires at the ignition harness.....also on the same relay pack there will be a 4 pin (small guage) harness that has 4 different colors coming off or it.....ur car has a 2nd starter wire.....which u will have to wire up a relay to activate that wire.  use the purple wire off the 4 pin harness as pin 85 on a standard relay.  hope this helps
Where theres is a wire there's a way.
black pearl 
Member - Posts: 7
Member spacespace
Joined: December 30, 2005
Location: United States
Posted: January 23, 2006 at 3:14 PM / IP Logged  

OK i think i got, for climate controls just connect ORANGE heavy gauge wire to white acc wire from the vehicle without a relay, right?

For the 2nd starter wire, the purple small gauge wire connects to a standard relay as follows: pin 85 purple wire, pins 86 and 87 connects to 12v 30amps fused, pin 87a to 2nd starter wire key side, and pin 30 to 2nd starter wire dash side, right? Do i need to use the remaining three small gauge wires for anyting else?

Any comments on where to connect the H2/5 GREY wire on the 530T window system, in order not to trigger the alarm when rolling up, down windows.

Thank you again for ur feedback!


Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Wednesday, July 23, 2025 • Copyright © 1999-2025 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer