| PASSIVE ANTI-THEFT | YES | TRANSPONDER | SEE NOTES |
| 12 VOLTS | RED / black | On C3 connector at BCM | + |
| | | The BCM is located directly below the glovebox. The connector layout is as follows: C1 (gray 72-pin), C2 (gray 72-pin), C3 (red 40-pin) and C4 (gray 68-pin) |
|
| IGNITION | Yellow | Ignition switch or C4 connector at BCM | + |
| | | The BCM is located directly below the glovebox. The connector layout is as follows: C1 (gray 72-pin), C2 (gray 72-pin), C3 (red 40-pin) and C4 (gray 68-pin) |
|
| ACCESSORY | Brown | Ignition switch or C4 connector at BCM | + |
| | | The BCM is located directly below the glovebox. The connector layout is as follows: C1 (gray 72-pin), C2 (gray 72-pin), C3 (red 40-pin) and C4 (gray 68-pin) |
|
| STARTER | SEE NOTES | | |
| | | No connection to the start wire is required. With proper Transponder bypass, the vehicle will crank automatically. |
|
| TACH SIGNAL | Use a fuel injector | | |
| FUEL INJECTOR | Opposite from Pink/black wire | At any injector on engine | AC |
| LOCK | Gray | On C3 connector at BCM | REV POL |
| | | These are the motor wires and you must wire it up as reverse polarity. The BCM is located directly below the glovebox. The connector layout is as follows: C1 (gray 72-pin), C2 (gray 72-pin), C3 (red 40-pin) and C4 (gray 68-pin) |
|
| UNLOCK | Tan | On C3 connector at BCM | REV POL |
| | | These are the motor wires and you must wire it up as reverse polarity. The BCM is located directly below the glovebox. The connector layout is as follows: C1 (gray 72-pin), C2 (gray 72-pin), C3 (red 40-pin) and C4 (gray 68-pin) |
|
| DOORPIN | SEE NOTES | | |
| | | GRAY/BLACK (driver's door) and TAN/WHITE (pass. door) Both are neg (-)and found at the C1 connector on the BCM. The BCM is located directly below the glovebox. The connector layout is as follows: C1 (gray 72-pin), C2 (gray 72-pin), C3 (red 40-pin) and C4 (gray 68-pin) |
|
| TRUNK PIN | ORANGE / black | On C1 connector at BCM | - |
| | | The BCM is located directly below the glovebox. The connector layout is as follows: C1 (gray 72-pin), C2 (gray 72-pin), C3 (red 40-pin) and C4 (gray 68-pin) |
|
| TRUNK RELEASE | Tan | At swicth or C2 connector on BCM | - |
| | | The BCM is located directly below the glovebox. The connector layout is as follows: C1 (gray 72-pin), C2 (gray 72-pin), C3 (red 40-pin) and C4 (gray 68-pin) |
|
| FACTORY ARM | Through OEM remote only | | |
| FACTORY DISARM | Through OEM remote only | | |
| BRAKESWITCH | Lt.blue | On C1 connector at BCM | + |
| | | The BCM is located directly below the glovebox. The connector layout is as follows: C1 (gray 72-pin), C2 (gray 72-pin), C3 (red 40-pin) and C4 (gray 68-pin) |
|
| PARKLIGHTS | Brown | In driver's kickpanel or C3 connector at BCM | + |
| | | The BCM is located directly below the glovebox. The connector layout is as follows: C1 (gray 72-pin), C2 (gray 72-pin), C3 (red 40-pin) and C4 (gray 68-pin) |
|
| HAND BRAKE | Lt.blue | On C1 connector at BCM | - |
| | | The BCM is located directly below the glovebox. The connector layout is as follows: C1 (gray 72-pin), C2 (gray 72-pin), C3 (red 40-pin) and C4 (gray 68-pin) |
|
| HORN | Tan | At steering column or C2 on BCM | - |
| | | The BCM is located directly below the glovebox. The connector layout is as follows: C1 (gray 72-pin), C2 (gray 72-pin), C3 (red 40-pin) and C4 (gray 68-pin) |
|
Topic Closed)
Members
Search
Register
Login
Printable version
