boa model 265b

Home / the12volt's Install Bay / Car Security and Convenience / boa model 265b (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

gmracer

Member - Posts: 4

Joined: December 04, 2006

Location: United States

Posted: May 20, 2007 at 9:55 AM / IP Logged

Im installing this in my 2001 Chevy Silverado, but I decided not to use the remote start. But When I tap into the power lock motor wires only the gray one accepts it, once I tap the tan only the passenger door works. Am I right in thinkin my truck is setup up DIrect Wired, Reversing Polarity system? Thats the diagram I used from the directions. Also the factory alarm i tap into the green wire behind the kickpanel near the ebrake release, the only wire left that I dont know if I use it or not is the RED / White for (-) Channel 2, what is that for? I included some pics

https://i83.photobucket.com/albums/j312/GMracer313/April22_2007097.jpg

https://i83.photobucket.com/albums/j312/GMracer313/April22_2007092.jpg

https://i83.photobucket.com/albums/j312/GMracer313/April22_2007104.jpg

https://i83.photobucket.com/albums/j312/GMracer313/April22_2007102.jpg

https://i83.photobucket.com/albums/j312/GMracer313/April22_2007101.jpg

Thanks in advance guys, I need this done today.

enice

Silver - Posts: 857

Joined: March 05, 2006

Location: New York, United States

Posted: May 20, 2007 at 6:55 PM / IP Logged

Your lock wire is light blue and your unlock wire is white and are located at the BCM. The BCM is located behind the drivers side of the dash. The plugs on the BCM face towards the rear of the vehicle. The parking lights are in pin A5 and the headlights are in pin A11. Always METER when possible. By they way the are positive triggers.

gmracer

Member - Posts: 4

Joined: December 04, 2006

Location: United States

Posted: May 20, 2007 at 8:33 PM / IP Logged

ok i got the lock wires figured out I just spliced em near the fuse panel, cuz I noticed the previous owner had the same setup and I took his out a while back due to it not working unless you were close to the truck, but now it locks, locks when I put the key on, but doesnt unlock, or flash the lights.... what does that RED / white (-) go to? also i noticed when I open my door my dome light wasnt turning on now.

enice

Silver - Posts: 857

Joined: March 05, 2006

Location: New York, United States

Posted: May 20, 2007 at 10:03 PM / IP Logged

The RED / white wire is a second channel for something like a trunk or window modules...etc. Did you connect the domelight output wire. Also what do you mean with "put the key on". Those two wires I posted earlier will do the trick .

gmracer

Member - Posts: 4

Joined: December 04, 2006

Location: United States

Posted: May 21, 2007 at 5:47 AM / IP Logged

I connected the white wire to the brown parking light wire, i didnt touch the dome light, and when I turn the truck on the doors lock themselves, but there is still no UNLOCK with the clicker

gmracer

Member - Posts: 4

Joined: December 04, 2006

Location: United States

Posted: May 22, 2007 at 3:55 PM / IP Logged

here you go man,

the lock wires:

https://i83.photobucket.com/albums/j312/GMracer313/DSCN4273.jpg

the 12v:

https://i83.photobucket.com/albums/j312/GMracer313/DSCN4275.jpg

the factory alarm disarm (light green wire in that harness):

https://i83.photobucket.com/albums/j312/GMracer313/DSCN4276.jpg

ground:

https://i83.photobucket.com/albums/j312/GMracer313/DSCN4278.jpg

parking lights(brown wire):

https://i83.photobucket.com/albums/j312/GMracer313/DSCN4277.jpg

then the big spew of wires, both reds each wire is explain where it went above first post.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

boa model 265b

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.