DIY: DRL for 96-00 Civics
Topic Closed)
Members
Search
Register
Login
For those of you non-Canadians who want Daytime Running Lights on your EK, here it is.
Parts Needed
-Automotive relay SPDT(5 point relay)-"T" Taps w/male spade connectors-Female spade connectors-25 amp blade fuse *shown later*-zip ties *not shown*-*Optional* Helms manual http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDAwMzc4NnM0MTNkZmQzMXk1NDE%3D.jpghttp://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDAwMzc5NnM0MTNkZmQzMXk1NDE%3D.jpg
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDAwMzcxNnM0MTNkZmQzMXk1NDE%3D.jpg
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDAwMzc2NnM0MTNkZmQzMXk1NDE%3D.jpg
Tools Needed-Phillips screwdriver
-wire stripper/crimperProcedure
1. Disconnect neg. cable on battery2. Remove lower dash panel -3 phillips screws and pull down
3. Locate green harness w/light wiring.(white arrow points to it, but hard to see in pic)
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDAwNDAxNnM0MTNkZmQzMXk1NDE%3D.jpgIt'll have RED / grn, RED / blue, RED / white, white wires going to it.4. Using two "T" taps, tap the RED / grn(parking light) wire and RED / white(low beam) wire.
5. Locate the power mirror harness(blue)
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDAwMzc3NnM0MTNkZmQzMXk1NDE%3D.jpg6. Using one "T" tap, tap the black wire at the bottom right of the harness.
7. For the main power wire, I rigged up a poor man's fuse harness using 2 female spade connectors. http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDAwMzcyNnM0MTNkZmQzMXk1NDE%3D.jpg
I cut the wire down the middle and put a female spade connector on each end.8. Plug one end of the fuse harness into the fuse panel.(red arrow-right next to fuse pulling tool) http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDAwNDE1NnM0MTNkZmQzMXk1NDE%3D.jpg
9. Find a mounting place for the relay. Then figure out the 3 other wire lengths from the relay to the "T" taps. The 3 other wires you run will be like this: male spade connector--wire--female spade connector
10. Relay connections(pins are marked) - 86-ground("T" tap in power mirror harness) - 85-RED / grn wire with "T" tap - 30-fuse panel - 87a-RED / white wire with "T" tap - 87-not used, put empty female spade connector on to prevent contact from anything
11. Reconnect neg. battery cable and test. The low beams should come on at key position 2(right before starting). http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDAwMzc0NnM0MTNkZmQzMXk1NDE%3D.jpg
12. Clean up wiring and mount the relay out of the way.(I used zip ties)http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDAwMzcwNnM0MTNkZmQzMXk1NDE%3D.jpg
13. Stand back and admire your new daytime running lights. :D
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wNDAwMzc1NnM0MTNkZmQzMXk1NDE%3D.jpgCheck it out! Headlights on, parking lights off!
Sorry, you can NOT post a reply.
This topic is closed.
Printable version
| You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
| Search the12volt.com |
Thursday, May 23, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved • Privacy Policy & Use of Cookies
