2002 Dodge Grand Caravan

Does anyone have an updated wiring diagram for a 2002 Dodge Grand Caravan?  Tony

Does anyone have an updated wiring diagram for a 2002 Dodge Caravan? Pino

|       ITEM      |     WIRE COLOR     |POL|       WIRE LOCATION        |

|              12V|lt blue/red (10A) *1|+  |ignition harness            ||          STARTER|yellow              |+  |ignition harness            ||   SECOND STARTER|PURPLE / brown *12    |-  |ignition harness            ||         IGNITION|pink/white          |+  |ignition harness            ||        ACCESSORY|*11                 |   |                            ||       POWER LOCK|PURPLE / green *3     |-  |conn. 3, pin 21 @ BCM *2    ||     POWER UNLOCK|same wire           |   |                            ||       LOCK MOTOR|tan/white           |   |conn. 2, pin 10 @ BCM *2    ||     UNLOCK MOTOR|tan/lt. green       |   |conn. 2, pin 28 @ BCM *2    ||    DISARM DEFEAT|tan/brown           |   |conn. 2, pin 26 @ BCM *2    || PARKING LIGHTS +|DO NOT USE          |   |                            || PARKING LIGHTS -|WHITE/ brown *8      |   |headlight switch            ||       HEADLIGHTS|same wire           |   |                            ||     DOOR TRIGGER|*4                  |-  |BCM *2                      || DOME SUPERVISION|use door trigger    |   |                            ||  TRUNK/HATCH PIN|PURPLE / orange *9    |-  |conn. 3, pin 29 @ BCM *2    ||         HOOD PIN|PURPLE / lt. blue     |-  |conn. 3, pin 30 @ BCM *2    ||TRNK/HTCH RELEASE|*10                 |   |*10                         ||  FCTRY ALARM ARM|PURPLE / lt. blue     |*5 |conn. 3, pin 14 @ BCM *2    ||FCTRY ALRM DISARM|same wire           |   |                            ||       TACHOMETER|*6                  |   |ignition coil pack          ||      SPEED SENSE|blue/orange         |   |PCM *7                      ||       BRAKE WIRE|WHITE/ tan           |+  |brake pedal switch          ||     HORN TRIGGER|GREEN/ purple        |-  |steering column             ||           WIPERS|brn/wht & brn/org   |+  |wiper motor                 ||  LF WINDOW UP/DN|org/lt grn - org/wht|A  |drivers window switch       ||  RF WINDOW UP/DN|org/tan - org/gry   |A  |drivers kick panel          ||  LR WINDOW UP/DN|org/blu - org/lt blu|A  |drivers kick panel          ||  RR WINDOW UP/DN|org/gry - org/grn   |A  |drivers kick panel          ||        RADIO 12V|gray/red            |+  |radio                       ||     RADIO GROUND|                    |   |                            ||     RADIO SWITCH|blue/pink           |+  |radio                       || RADIO ILLUMINATE|ORANGE / tan          |+  |radio                       ||       LF SPEAKER|green - grn/brn     |   |radio                       ||       RF SPEAKER|gray - gray/brn     |   |radio                       ||       LR SPEAKER|grn/blu - grn/org   |   |radio                       ||       RR SPEAKER|gry/blu - gry/org   |   |radio                       |

Notes:

NOTE:  Chrysler vehicles that use a gray ignition key have an immobilizer system that needs to be bypassed when remote starting.  *1 This wire is rated at 10 amps only. If installing any system with high current outputs, go to battery for 12v.  *2 The BCM is in the drivers kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs.  *3 Lock is negative trigger thru a 5.3K ohm resistor. Unlock is negative trigger thru a 2.0K ohm resistor. MUST use relays.  *4 There are separate door triggers for each door, they are all in connector 3 at the BCM. The driver door trigger is purple in pin 6, the passenger door is PURPLE / white in pin 7, the left sliding door is PURPLE / gray in pin 8, and the right sliding door is purple / YELLOW in pin 5. Use all four and diode isolate each. .  *5 Arm is negative trigger thru a 1.5K ohm resistor, this will also lock the doors. Disarm is negative trigger thru a 9.1K ohm resistor, if use double pulse this will also unlock the doors. MUST use relays.  *6 On the 2.4L use blue/green or blue/tan. On the 3.3L/3.8L use blue/green, blue/tan or blue/orange.   *7 The PCM is behind the driver side headlight. VSS is in the gray plug, pin 66.  *8 The parking lights are negative trigger thru a 2.1K ohm resistor. The headlights are negative trigger thru a 790 ohm resistor. There is a rest resistance on the wire, so MUST use a relay to isolate away from the switch. See directfax document # 1082 for wiring information.  *9 A diode must be placed inline on this wire to avoid problems with the dome lights and parking lights.  *10 Hatch release is PURPLE / tan in connector 2, pin 6 at the BCM. It is negative trigger thru a 1.69K ohm resistor. Left power sliding door is PURPLE / blue in connector 3, pin 1 at the BCM. It is negative trigger thru a 1.5K ohm resistor. Right power sliding door is the same wire as the left and it is negative trigger thru a 2.7K ohm resistor. Must use relays.  *11 Accessory is not required for remote start.  *12 The second starter wire is negative trigger thru a 180 ohm resistor. MUST use relay.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Thanks, I received the wiring diagram. But I need advise. The outlet 4 is optional for some models. My car doesn't have that one, so I need  to identify what cables in the floor I need to pin to feed the power outlet for cellular phone in the removal floor console.Pino

Do you have a DMM ? Use this to target the wires necessary for the cell phone attachment and hardwire it into the wires that you find with the DMM.Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Is there a large guage BLACK/ orange wire at the ignition harness? IF so test it with a DMM, if it is an ignition wire try hooking that up.

hook up as accessory.