Can you put a dye in the resin

Home / the12volt's Install Bay / Fiberglass, Fabrication, and Interiors / Can you put a dye in the resin (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

total_overkill

Copper - Posts: 93

Joined: November 24, 2005

Location: Canada

Posted: January 12, 2006 at 7:34 PM / IP Logged

Can you change the resin color with a dye or get a differnt color resin\hardner combo. I dont want pigments or addatives. I want to do blue lenses on the headlights and want clarity. If it doesnt turn out im just going to make em overlays\eyebrows

40 grit has saved my life sometimes =[

Search for other posts by total_overkill

auex

Platinum - Posts: 5,041

This member has made a donation to the12volt.com. Click here for more info.

Joined: December 23, 2002

Location: Arizona, United States

Posted: January 12, 2006 at 9:52 PM / IP Logged

I don't know why you would use resin to tint headlights. There has to be easier ways.

Certified Security Specialist

Always check info with a digital multimeter.

I promise to be good.

Tell Darwin I sent you.

I've been sick lately, sorry I won't be on much.

total_overkill

Copper - Posts: 93

Joined: November 24, 2005

Location: Canada

Posted: January 12, 2006 at 10:31 PM / IP Logged

I think your right

40 grit has saved my life sometimes =[

placid warrior

Silver - Posts: 357

Joined: November 06, 2004

Location: Canada

Posted: January 12, 2006 at 11:21 PM / IP Logged

Window tint might work just fine, just make sure the lenses are clean from dirt and grime. Or use a color marker, lol, jk. But yea u can put dye in the resin, i just wouldnt do it for headlight covers.

Search for other posts by placid warrior

97blackrodeo

Member - Posts: 34

Joined: May 27, 2005

Location: United States

Posted: January 13, 2006 at 5:51 PM / IP Logged

Your best bet would be to go with a basecoat/clear coat. Tint the clear coat by adding some base. i mean very little base will do the job. Experiment with it first before you shoot it. Then wet sand and buff and they will look like glass.

bellsracer

Silver - Posts: 703

Joined: January 14, 2006

Location: United States

Posted: January 17, 2006 at 3:56 AM / IP Logged

It would be best to go with the base coat / clear coat combo. For your base coat, I would use a candy of some sort I love House of Color candies. They are translucent, so it will allow light to pass through. A solid base paint will make the headlights illegal in most states... now that i think about it almost all states have restrictions on tinting headlights, unless it is a show car. but I would recommend painting it. you can't use window tint for it. the heat from most headlights (65 watt and higher definitely; 55 watt on some models) would heat-warp the tint in about 4-5 months. (talking from experience for an art project ^-^;;)

The part I am most concerned with would be the sanding. You are going to have to be very careful on sanding the headlights (220 grit+ preferably 260 or higher considering it's acrylic) and sanding it only in the area you want painted. If you are painting the whole assembly, then I would worry about the sanding right in front of the bulbs themselves. the paint might distort the light, or become discolored from the heat... I would go to a pick and pull and pull an assembly from there for a test. This can go either very well and look great or be exspensive to replace the headlights.

Never send your ducks to eagle school.

The difference between ordinary and extraordinary is that little extra.

The 3Ls of life: Learn from the Past, Live for the Present, Look to the Future.

97blackrodeo

Member - Posts: 34

Joined: May 27, 2005

Location: United States

Posted: January 17, 2006 at 10:55 AM / IP Logged

Good points bellsracer, but i had something different in mind. When I said basecoat/clearcoat, i didnt mean the traditonal paint technique(basecoat-wetsand-cleacoat-wetsand and buff). I meant mix a very little bit of base into the clear and shoot it mixed together. There is a ratio where the base actually tints the clear, and doesnt overwhelm it. This ratio is different with every brandand color so there is no set number. Experimenting is the only way with this technique. I have done both headlights and taillights like this with incredible results. When you have achieved the color you want on the lense, wet sand with 1000 grit and buff LIGHTLY. I hope this has been helpful.

placid warrior

Silver - Posts: 357

Joined: November 06, 2004

Location: Canada

Posted: January 17, 2006 at 12:04 PM / IP Logged

So do u like sand the plastic down before u paint it? what about a clear flexible primer (they do have it). How long does it last? wouldnt it flake off once it got a break in the paint from road debris?

97blackrodeo

Member - Posts: 34

Joined: May 27, 2005

Location: United States

Posted: January 17, 2006 at 12:31 PM / IP Logged

Yes as with any plastic you prep it as the materials requires, and add the flex additive if necessary. Typically, I dont add flex additive or primer. For example, with honda civic headlights, I hit it with 600 grit or so, prep sol the surface and shoot the base/clear mix. let it dry fully, wet sand it a little, and spray again. When all is said and done, I hit it with 1000 or so, and buff it by hand lightly.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Can you put a dye in the resin

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.