why fuse within 18 inches of battery?

Home / the12volt's Install Bay / Car Audio / why fuse within 18 inches of battery? (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

thumpinbass

Member - Posts: 10

Joined: January 28, 2008

Posted: October 14, 2008 at 11:12 PM / IP Logged

You keep hearing that you should have an inline fuse 18" from your battery. Why 18"? Why not 12" or 24"?

OK, so now the reason why I ask. I have a kicker inline fuse that I can use at my battery. It is not weatherproof to put in my engine, so I was going to run my power wire through the firewall (which I would need to do anyways) and put the inline fused just inside the cab of my truck. Then run it back to my amps.

It will be very close to being 18" to where I put the inline fuse at, but could be up to 24". Is this a problem? Is there a reason why everyone says 18". I'm just curious, plus want to know if 24" will be ok.

Thanks for your help!

Allen

audiocableguy

Copper - Posts: 630

Joined: January 27, 2003

Location: Idaho, United States

Posted: October 14, 2008 at 11:53 PM / IP Logged

The Inline fuse is there to protect the wire. Period. The closer to the battery, the better protected that wire will be. The fuse should be installed before going through the firewall even if it is less than 18".

Use a rubber or hard plastic grommet if you can't use a factory one.

IASCA specs 18" Max, the Marine Safety Reg. says 12" Max. Closer the better.

megaman

Copper - Posts: 385

Joined: June 24, 2008

Location: Montana, United States

Posted: October 15, 2008 at 8:44 AM / IP Logged

I hear this a lot from my customers doing thier own installs. As stated above, the fuse protects the wire. If you put the fuse after the firewall, then there's the chance that if the wire were to be chaffed by the hole in the firewall that it runs through, then it could short to ground and burn up. If you put the fuse as close to the battery as possible, then the fuse will do it's job if the wire were to become damaged and short to ground. Frankly there's no real reason to put the inline fuse inside the cab at all.

thumpinbass

Member - Posts: 10

Joined: January 28, 2008

Posted: October 15, 2008 at 9:33 AM / IP Logged

I knew why the fuse is there. I have done numerous installs before, nothing competition though. I was just curious why it's always recommended to be 18". That's all.

And the reason why I asked about doing it inside (the inline fuse) is because I happen to have an inline fuse already, but not made for the engine compartment, so why spend all the money on another one if there was a chance I could use the one I currently have. I had just checked and the inline fuse would have been right around 12" - 18" from the battery if I had decided to do it inside the cab since my battery is right against the firewall in my AV.

I will be using the stinger grommet for 0g for my firewall.

All my wiring is stinger products and all my car audio is Kicker.

Allen

DYohn

Moderator - Posts: 10,741

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

Joined: April 22, 2003

Location: Arizona, United States

Posted: October 15, 2008 at 9:57 AM / IP Logged

thumpinbass wrote:

so why spend all the money on another one if there was a chance I could use the one I currently have.

Because it is always better to do it correctly than to just "make it work." That's the difference between an installer and just some guy who knows how to wire car stereo. why fuse within 18 inches of battery? -- posted image.

Support the12volt.com

KPierson

Platinum - Posts: 3,527

This member consistently provides reliable information

Joined: April 14, 2005

Location: Ohio, United States

Posted: October 15, 2008 at 12:39 PM / IP Logged

I've always heard "within 18"" of the battery. You can go less, it's just not a good idea to go more. If the fuse is within 18" of the battery there isn't much room for the wire to short out.

A few years back a few companies had fuse holders that mounted right to the battery - that is technically the best way to go as that way the entire wire is protected. However, that isn't aslways feasable due to space restrictions.

Kevin Pierson

audiocableguy

Copper - Posts: 630

Joined: January 27, 2003

Location: Idaho, United States

Posted: October 15, 2008 at 3:01 PM / IP Logged

Buss/Blue Sea Systems offers these terminal fuses that have a bracket that mounts directly to the battery post, very clean and somewhat cost effective.

http://bluesea.com/category/5/22/productline/overview/379

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

why fuse within 18 inches of battery?

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.