fuse box melted

Home / the12volt's Install Bay / Car Audio / fuse box melted (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

Jay22

Copper - Posts: 73

Joined: April 27, 2004

Location: Canada

Posted: May 14, 2004 at 3:59 PM / IP Logged

I have a PPI PC2150 running my 3 alpine S 12's. I have me wiring ran off the battery 4 gauge 150 amp fuse. It all splits of at a rockford fuse to 8 gauge. One day I had it on and it shut off so i checked it out and the plastic part on the rockford was melted. so I switched to the other side and after one day it melted too.

Anyone know how???

neo

Member - Posts: 19

Joined: May 14, 2004

Location: United States

Posted: May 14, 2004 at 4:06 PM / IP Logged

You probably have a short some where. The hot is probably in contact with a ground, such as an unpainted portion on the vehicle. Check your hot wire for any problems

Neo,Solving All The Worlds Problems

forbidden

Platinum - Posts: 5,352

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

Joined: November 01, 2003

Location: Alberta, Canada

Posted: May 14, 2004 at 4:35 PM / IP Logged

What is the size of the fuse in the amplifier? From your wording above it seems that you have a 4 gauge wire running from the battery, through a big fuse (not the problem), continues on with the 4 gauge until it hits a Rockford fused distribution block? where it continues on to the amp as an 8 gauge line. The melting is at the Rockford piece correct. The amplifier is still operating is it not? What size ground wire do you have, where is it grounded to. If you have a fused distro block (now 1/2 melted) what size fuse is in it as compared to the one in the amp?

Top Secret, I can tell you but then my wife will kill me.

stevdart

Platinum - Posts: 5,816

This member consistently provides reliable information

Joined: January 24, 2004

Location: Pennsylvania, United States

Posted: May 14, 2004 at 4:37 PM / IP Logged

If your power wire fuse at the battery didn't blow, then the power is OK. What is the plastic Rockford fuse you are talking about? Are you running more than the PPI you described?

Build the box so that it performs well in the worst case scenario and, in return, it will reward you at all times.

kgerry

Platinum - Posts: 3,455

Joined: February 07, 2004

Location: Saskatchewan, Canada

Posted: May 14, 2004 at 6:28 PM / IP Logged

i'm presuming like others are i think that it's your fused distribution block that is melting? if so and the amps are still working then it sounds like you are drawing excessive current throught the fuse/dist block... or you got a defective one... keep in mind that AGU ( assuming you are using an AGU block ) circuits are only rated to 60 amps (although some manufacturers do make 80 amp AGU fuses ) what are the legs fused at?

you may need to step up to a beefier dist block that uses Maxi or mini ANL's that will allow for greater current draw thru the individual legs....

but hey, what do i know?

Kevin Gerry

Certified Electronics Technician

MECP First Class Installer

Owner/Installer

Classic Car Audio

since 1979

dudek38

Copper - Posts: 250

Joined: March 28, 2004

Location: United States

Posted: May 16, 2004 at 10:44 PM / IP Logged

isn't a 150 amp fuse too big in case there was a short, allowing something to melt?

owner of

Motion Marine & Car Audio

the florida keys

flatulatta

Silver - Posts: 356

Joined: August 28, 2003

Location: United States

Posted: May 17, 2004 at 7:47 AM / IP Logged

well depends on how much draw he is getting... we need to know wut else he has.... i assume he has another amp we do not know about unless he just likes the distro block for some reason

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

fuse box melted

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.