keep or trash?

Home / the12volt's Install Bay / Car Audio / keep or trash? (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Topic Next Topic >

spootydlux4

Copper - Posts: 149

Joined: October 03, 2004

Location: United States

Posted: December 26, 2004 at 1:07 AM / IP Logged

today i was talkin to my mom's friend about car audio and he said he had an amp from his last car that he'd give me so it turned out to be a kicker impulse 652xi. heres the specs, it seems like a decent little amp. but is it worth powering my fronts or is it trash? oh and bout that crossover, its just a switch? so if i used to for my components i would just switch it to 110 eh? but my headunit has built in crossovers too, so no biggee there.

rated power--- rms power @ 12v

65 watts per channel into 4ohm ( stereo)

95 watts per channel into 2ohm (stereo)

190 watts ( bridge/mono into 4ohm)

dynamic power @ 14v

90 watts per channel into 4ohm( stereo)

130 watts per channel into 2ohm (stereo)

260 watts (bridge/mono)into 4ohm)

Frequency Response 20Hz-20kHz ±0.5dB

High Level Input Sensitivity 1V-10V

Low level Input Sensitivity 150mV-3.0V

Signal-to-Noise Ratio >90dB, a-weighted, re: rated power

Active Electronic Crossover 18dB/octave, selectable @ 70Hz or 110 Hz; selectable high pass, low pass, all pass

KICKEQ Bass Boost Variable to +18dB, centered @ 40Hz

KICKEQ Treble Boost Variable to +12dB, centered @ 12kHz .

085% THD

blah blah blah blah

Back to Top

bdl666

Silver - Posts: 330

Joined: December 31, 2002

Location: United States

Posted: December 26, 2004 at 2:15 AM / IP Logged

Keep it.

Back to Top

wheelerdr

Copper - Posts: 337

Joined: October 25, 2004

Location: Louisiana, United States

Posted: December 26, 2004 at 2:16 AM / IP Logged

for free i would go ahead and keep it for now

Back to Top

DYohn

Moderator - Posts: 10,741

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

Joined: April 22, 2003

Location: Arizona, United States

Posted: December 26, 2004 at 9:29 AM / IP Logged

If you use your HU crossiver, set the amp to "all pass." If you use the amp crossover, set it to "high pass" and yes, 110 would be fine, as long as your sub is low-passed that high. If the sub is closer to 70, set the high pass on this amp to 70. Leave that bass and treble boost set to OFF (or "zero.")

Support the12volt.com

Back to Top

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

keep or trash?

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.