the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Old System New Popping


Post ReplyPost New Topic
< Prev Topic Next Topic >
porter843 
Member - Posts: 4
Member spacespace
Joined: March 07, 2005
Location: United States
Posted: March 07, 2005 at 4:55 PM / IP Logged  

I have been installing car audio for about 13 years now and I can't figure this one out.  I have had a system in my car for over a year now and yesterday when I got in the car and started up the engine I got these unbareable pops (boom, boom, boom,...) the sounded like my head unit was on full blast when in fact I had turned it down to ZERO.  I turned the system off.  Shut down my car, checked everything in the trunk and it looked OK.  I turned the system back on without starting the car and got the same thing.  I waited about an hour turned it on and it would play but there was a whine with the engine off and the levels were severly low.  I repaced the head unit today and I still have the same problems.  I don't have any equipment with me to test my amplifier but I would like to get this taken care of while I am still away from home.  I can play the new head unit with normal levels but the whine is rediculous and the popping when I change between sources is unearthing.  I also hear my CD player spin up and search.  This is very annoying as well.  I didn't have this problem for the last year, it all just started yesterday.  Can you offer any suggestions.  I was contemplating changing out my high side amp.  

Head Unit  Pioneer DEH-7400MP
| |
| - Front High > 80 Hz -- Precision Power PCX-280 - 4 Ohms
|                                 Polk MMC6500 Component Speakers
|
--- Sub < 80 Hz -- Precision Power PCX-1250 - 2 Ohms
                         2 - SoundStream Rubicon 15 Subs
That's my setup.  Please HELP!
OK, I ran a new ground wire from my head unit, problem got worse.  I swapped out my highs amp just to check and the didn't hear the mute pop.  so I plugged my PPI amp back up and now, the whole system is screwed.  When I turn on the system I get this un-nerving noise that hard to explain without hearing it.  It just sounds like bbbbbbbbbbbbbbbbb.  Except at 135 dB.  The system plays for a couple of seconds and then starts making that noise.  The weird thing is that when I take the volume all of the way down to 1 and make the transition to 0 it starts making that noise every time.  I have to turn off the switch because I have to hold the source button down too long to stop it normally.

Head Unit  Pioneer DEH-P80MP

| |
| - Front High > 80 Hz -- Precision Power PCX-280
|                                 Polk MMC6500 Component Speakers - 4 Ohms
|
--- Sub < 80 Hz -- Precision Power PCX-1250 - 2 Ohms
                         2 - SoundStream Rubicon 15 Subs - 4 Ohm Subs

This is my new setup after changing out my head unit.  The system played for a few days normally after I replaced the head unit and all I heard was alternator whine and the pop when I transitioned from 1 to 0 on the volume level.

porter843
"Life is tough, it's even tougher when you are stupid" -- John Wayne
DYohn 
Moderator - Posts: 10,741
Moderator spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spacespace
Joined: April 22, 2003
Location: Arizona, United States
Posted: March 07, 2005 at 5:47 PM / IP Logged  
Pull your fuse for the sub amp and see if its the mains.  If so, pull that fuse, replace the sub amp fuse and try again.  If one amp is causing the noise but the other is OK, then one amp has taken a dump and needs repair/replacement.  If BOTH amps are making noise you probably have a crushed or damaged RCA cable or two.
Support the12volt.com
porter843 
Member - Posts: 4
Member spacespace
Joined: March 07, 2005
Location: United States
Posted: March 07, 2005 at 9:15 PM / IP Logged  

I pulled the RCA cables from both amps and the buzzing and everything went away.  So the problem is between my head unit and my amps I agree.  I found out that if I pull either one of the RCA sides out of my sub amp the bbbbbbb problem goes away.  There appears to be some sort of loop created when I plug in both right and left RCA's to my sub amp. 

I will check my RCA cables front to back and fill you in when and if I find anything.  Thanks for the input.

porter843
"Life is tough, it's even tougher when you are stupid" -- John Wayne
porter843 
Member - Posts: 4
Member spacespace
Joined: March 07, 2005
Location: United States
Posted: March 09, 2005 at 11:55 PM / IP Logged  

I pulled the power from the sub amp and my highs amp popped with the same noise.  Then when I put the power back in and pulled the power from the highs amp the sub amp really rumbles, until, I pull out one of the RCA plugs.  I replaced my RCA cables and still the same thing, both amps making that bbbbbbb sound. 

What I am wondering is, could something in my alternator have gone bad to blow both of my amps?  Has anyone ever heard of this happening?  I don't want to replace both of my amps until I find out what caused my other ones to blow!!!

Any suggestions.

porter843
"Life is tough, it's even tougher when you are stupid" -- John Wayne
DYohn 
Moderator - Posts: 10,741
Moderator spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spacespace
Joined: April 22, 2003
Location: Arizona, United States
Posted: March 10, 2005 at 8:35 AM / IP Logged  

You replaced the RCA cables completely?  Sounds like a couple possible causes might be

1) bad or loose ground somewhere, maybe at the amps, inside the engine compartment, at the battery or at the HU 

2) Head unit went bad.

Support the12volt.com
porter843 
Member - Posts: 4
Member spacespace
Joined: March 07, 2005
Location: United States
Posted: March 12, 2005 at 8:58 PM / IP Logged  

Today,  I used a jumper to connect the accessory wire to my remote to turn my amps on and I plugged in a portable CD player.  Everything worked fine.  So, I have to go get another head unit to replace this one.  I have never installed a head unit that was bad out of the box, what a pain in the neck.

Thanks for your help,

porter843
"Life is tough, it's even tougher when you are stupid" -- John Wayne

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Saturday, April 27, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer