find preamp voltage with multimeter.

Home / the12volt's Install Bay / Car Audio / find preamp voltage with multimeter. (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

luckydevil

Silver - Posts: 365

Joined: July 04, 2005

Location: United States

Posted: August 12, 2005 at 8:53 PM / IP Logged

After searching and reading through about 100 posts on here I still couldn't find the proper way to find the preamp voltage. I ended up calling a relative and he told me.

It is as simple as taking one of the rca's going to the amp from the head unit and touching one multimeter lead to the inner tip and the other lead to the outer part. Be sure to have the multimeter in AC mode.

On a side note when I changed my volume the output voltage also changed correspondingly. Keep that in mind when testing it.

Just posting this so anyone else looking for the info will see it.

luckydevil

Silver - Posts: 365

Joined: July 04, 2005

Location: United States

Posted: August 12, 2005 at 8:55 PM / IP Logged

Forgot to add that I used a 60hz test tone for this.

stevdart

Platinum - Posts: 5,816

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member consistently provides reliable information

Joined: January 24, 2004

Location: Pennsylvania, United States

Posted: August 13, 2005 at 7:52 AM / IP Logged

I've tested for AC voltage at the amp's speaker outputs this way. Gain all the way to minimum, head unit at full, test tone playing on CD, speakers disconnected. This gives you the voltage that the amplifier is starting with.

Build the box so that it performs well in the worst case scenario and, in return, it will reward you at all times.

luckydevil

Silver - Posts: 365

Joined: July 04, 2005

Location: United States

Posted: August 13, 2005 at 8:57 AM / IP Logged

I've read that method many times on here and that is what I initially tried, but it doesn't give the actual preamp voltage.

Using that method I was getting different numbers on different amps. One was reading 8v and the other was reading 6v with both at minimum gain when my actual preamp voltage is ~2v.

lostracer

Member - Posts: 32

Joined: November 02, 2004

Location: California, United States

Posted: August 13, 2005 at 9:25 AM / IP Logged

I've seen most decks use a bout a 2v pre amp. Cheapers ones may be a little less. And then the higher models just go up from there...Mine was listed in the manual under technical specifications.

I did the same thing for matching them. Multimeter to the speaker outputs and set from there.

"Using that method I was getting different numbers on different amps. One was reading 8v and the other was reading 6v with both at minimum gain when my actual preamp voltage is ~2v."

That method is used for gain matching. That 6 and 8v you were reading were most likely the gain off of the amp.

The One&Only!

DYohn

Moderator - Posts: 10,741

This member has been recognized as an authority in Electrical Theory. Click here for more info.

Joined: April 22, 2003

Location: Arizona, United States

Posted: August 13, 2005 at 10:12 AM / IP Logged

A note of caution: it is pretty easy to short out your preamp using meter leads on RCA connectors, especially with the "fat" probe tips on some lead sets. All you have to do is let the probe touching the inner conductor lean over and touch the outer ring and poof, you can blow the output stage on some preamps. If you want to directly measure pre-out voltage level a better way is to build a mating RCA connector with wires that can be split, stripped and used as your meter connection point. And use gripper probes on your meter so you don't have to hold them by hand.

Support the12volt.com

stevdart

Platinum - Posts: 5,816

Joined: January 24, 2004

Location: Pennsylvania, United States

Posted: August 14, 2005 at 9:05 PM / IP Logged

I'm still foggy about this, so would someone set me straight? Voltage is not summed, or is it? When reading the RCA, if the left channel reads 4 volts and the right channel reads 4 volts, it's still just 4 volts total? Which means reading either channel on the RCA will give you the deck output? And a valuable tip there, DYohn. I'm glad to know that now.

Build the box so that it performs well in the worst case scenario and, in return, it will reward you at all times.

DYohn

Moderator - Posts: 10,741

Joined: April 22, 2003

Location: Arizona, United States

Posted: August 14, 2005 at 9:13 PM / IP Logged

Stevdart you are correct, preamp output voltage is per channel. I don't understand some of the earlier comments made by others....

Support the12volt.com

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

find preamp voltage with multimeter.

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.