the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2008 nissan sentra, bypass


Post ReplyPost New Topic
< Prev Topic Next Topic >
techman93 
Silver - Posts: 591
Silver spacespace
Joined: October 28, 2006
Location: Pennsylvania, United States
Posted: February 06, 2008 at 12:07 AM / IP Logged  
I did an install today at work using an XK07 with the PKN3 firmware for a 2008 Nissan Sentra. It seemed to program fine like in the directions but it did not override the transponder. I hooked it up at the OBDII connector and at the cluster. Neither locations worked. I think that there must be a change between the 2007 and 2008. Has anyone had any experience yet with this?
The wire I'm test'n isn't doin' what it's supposed to be doin'... I am so glad I printed that tech sheet, with the wrong info.
Do it right the first time... or I might have to fix it for ya
extreme1 
Silver - Posts: 1,070
Silver spacespace
Joined: February 12, 2003
Location: Canada
Posted: February 06, 2008 at 12:17 AM / IP Logged  
was the problem a no crank issue? if you you have to wire a relay up under the hood.
Shaughn Murley
Install Manager, Dealer Services
Visions Electronics
Red Deer, Alberta
techman93 
Silver - Posts: 591
Silver spacespace
Joined: October 28, 2006
Location: Pennsylvania, United States
Posted: February 06, 2008 at 6:59 AM / IP Logged  
Yeah there was no crank on starter but if I put key in ignition it would work fine. I am going to check if there was a change in firmware and if I don't get the XK07 to work I will need to wrap a key to hide under the dash.
The wire I'm test'n isn't doin' what it's supposed to be doin'... I am so glad I printed that tech sheet, with the wrong info.
Do it right the first time... or I might have to fix it for ya
techman93 
Silver - Posts: 591
Silver spacespace
Joined: October 28, 2006
Location: Pennsylvania, United States
Posted: February 06, 2008 at 7:17 PM / IP Logged  
I got into work this morning and my boss informed me he flashed the module and to "try again" to program it to the car. I had very little faith since it didn't work yesterday. I plugged it back in and reset it. Turned the ignition on and the module did what it did with the LED flashing then went off to indicate it was programmed. I pushed remote to start and gosh darn it, it freakin started!!! I wish that my bosses dad would have done what he was supposed to by flashing the module. All he said was the parts were on his desk and it was a 2008 Nissan.
The wire I'm test'n isn't doin' what it's supposed to be doin'... I am so glad I printed that tech sheet, with the wrong info.
Do it right the first time... or I might have to fix it for ya
hydroz_23 
Copper - Posts: 97
Copper spacespace
Joined: November 20, 2006
Location: United States
Posted: February 06, 2008 at 9:33 PM / IP Logged  
there was a firmware update released recently to allow xk07 to work with   
sentra and versa. no need for a relay under the hood. only on the altima

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Monday, April 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer