07 g6 can sl2 and ultra start

Home / the12volt's Install Bay / Car Security and Convenience / 07 g6 can sl2 and ultra start (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

justinthurn

Member - Posts: 24

Joined: December 04, 2002

Location: United States

Posted: February 15, 2010 at 9:51 AM / IP Logged

installing an ultra start 3255 on an 07 pontiac G6 with the fortin can-sl2. the bypass kit programs successfully according to the instructions but will not remote start, the starter tries to but apparently the bypass isnt set up correctly. this is my first install on a gm vehicle with not starter wire to hook up. the can-sl2 has an accessory output that shows to hook up to the car, the ultra start also has an accessory wire to hook up to the car. i have tried with just the can-sl2 wire hooked up and also with both wires hooked up, same result. i am thinking it is something obvious, any help is appreciated. thanks.

prdjr165

Copper - Posts: 293

Joined: October 31, 2002

Location: Illinois, United States

Posted: February 16, 2010 at 10:03 AM / IP Logged

the accy connection on the can-sl2 is an input..so go ahead and connect it to the accy wire at the ign harness.when programming did you start the car when the led started flashing?

justinthurn

Member - Posts: 24

Joined: December 04, 2002

Location: United States

Posted: February 16, 2010 at 10:21 AM / IP Logged

Right now i have the accy of the can-sl2 hooked up to the accy wire at the ignition harness. the ignition wire from the remote starter is not hooked up at all. I have also tried with a jumper wire so the can-slt accy and the remote start accy are hooked up to the ignition accy. Both ways end with the same result. the can-sl2 will program, i do not start the car, turn the key to ignition, the led goes out, turn the key off. try to remote start, it tries, then fails. if i put the key in and turn to ignition (not start) at just the right time, it will remote start.

prdjr165

Copper - Posts: 293

Joined: October 31, 2002

Location: Illinois, United States

Posted: February 16, 2010 at 10:25 AM / IP Logged

start the car with the key when the led starts flashing,that is what you have to do for gm cars.also hook up the accy wire from the remote start to the accy (brown)wire at the ign harness.

tedmond

Gold - Posts: 4,610

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: January 06, 2007

Location: Ontario, Canada

Posted: February 16, 2010 at 5:07 PM / IP Logged

you need to wire the acc and ignition wires from the remote start to the wires at the ignition barrel. also make sure the red and white wire is interrupted during remote start.

i hope you did not try programming it more than 5 times. if you do the unit will go into tamper mode and will lock out, that means you will need to get a new can-sl2

Ted

2nd Year Tier 1 Medical School

Still installing as a hobby...pays for groceries

Compustar Expert

ropuma

Copper - Posts: 102

Joined: February 16, 2010

Location: Illinois, United States

Posted: February 17, 2010 at 8:47 PM / IP Logged

Do you still need help?

justinthurn

Member - Posts: 24

Joined: December 04, 2002

Location: United States

Posted: February 18, 2010 at 8:38 AM / IP Logged

I havent had a chance to work on the car yet, hopefully this afternoon. thanks.

justinthurn

Member - Posts: 24

Joined: December 04, 2002

Location: United States

Posted: February 18, 2010 at 8:17 PM / IP Logged

well, still no luck. I have connected as described and reprogrammed by starting the vehicle, nothing has changed. This is the 4th program of the can-sl2 so i am close to the limit. It does try to start as in, it acts like the key when it turns to ignition, but then cuts out, definitely seems like a bypass issue. I do have a relay hooked up between the RED / white wire on the transponder connector (there is also a RED / white wire on the iginition connector, but I havent touched that one) I did try starting it with the RED / white wire disconnected completely from and still got the same result. Really at a loss now.

tedmond

Gold - Posts: 4,610

Joined: January 06, 2007

Location: Ontario, Canada

Posted: February 19, 2010 at 6:42 AM / IP Logged

dont program the bypass anymore. it is programmed correctly already. a bypass is able to program correctly but its faulty wiring that will not allow it to start.

disconnect power and connectiosn to the can sl2, place a key into the ignition and try to remote start. if it starts its bypass issues, if it doesnt, you are missing acc or ignition wires.

Ted

2nd Year Tier 1 Medical School

Still installing as a hobby...pays for groceries

Compustar Expert

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

07 g6 can sl2 and ultra start

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.