viper 5701 on 1997 honda civic

Hey guys I'm trying to get my alarm installed on my 97 Civic w/auto trans. The alarm part went smoothly but not the remote start. I can start the car with the key and press the remote start and it will stay running when the key is removed and shutdown with the remote. It will not however remote start alone with the remote. The parking lights and guage come on but no attempts to start. If you guys could look over my wiring diagram or if you have any suggestions that would be great. H1 MAIN HARNESS RED / WHITE/ /////////TRUNK RELEASE OU///////////////NO CONNECTION RED / //////////////////////12VDC CONSTANT IN/////////////CONSTANT 12V FUSE BOX BROWN / /////////////////SIREN OU////////////////////////////////RED(SIREN) WHITE/ BROWN / ////PARKING LIGHT ISO WIRE/////NO CONNECTION BLACK/ ///////////////////CHASSIS GROUND VIOLET///////////////////POS DOOR TRIGGER///////////////NO CONNECTION BLUE//////////////////////TRUNKPIN/////////////////////////////////BLUE/BLACK(DRKICK)DI GREEN/ //////////////////NEG DOOR TRIGGER///////////////LGTGRN/RED(ABV FUSE PANEL) BLACK/ WHITE/ //////DOME LIGHT SUP/////////////////////NO CONNECTION WHITE/ BLUE//////////REMOTE START///////////////////////NO CONNECTION WHITE/ //////////////////PARKING LIGHT OU///////////////////RED / BLACK(DRKICK) ORANGE / //////////////GROUND WHEN ARMED OU H3 REMOTE START HARNESS PINK//////////////////BLACK-YELLOW RED-WHITE/ //////WHITE ORANGE / ///////// / YELLOW VIOLET//////////////STARTER SIDE BLACK-WHITE GREEN/ /////////////KEY SIDE BLACK-WHITE RED / //////////////////WHITE PINK-WHITE/ /////WHITE BLACK PINK-BLACK/ /////NO CONNECTION RED-BLACK/ //////WHITE BLUE/////////////////UNLOCK OUTPUT(500mA) GREEN/ /////////////LOCK OUTPUT(500mA) H2 HARNESS LGTGREEN/ BLACK/ //////OE ALARM DISARM//////////////NO CONNECTION ORANGE / BLACK/ //////////AUX 4 OU////////////////////////////NO CONNECTION GREEN / WHITE     //////////////OE ALARM ARM/////////////NO CONNECTION VIOLET/BLACK/ /////////////AUX 2 OU//////////////////////////NO CONNECTION WHITE/ BLACK/ //////////////AUX 3 OU/////////////////////////////NO CONNECTION WHITE/ VIOLET/////////////AUX 1 OU/////////////////////////////NO CONNECTION GREY/BLACK/ ///////////////DIESEL WTS IN///////////////////NO CONNECTION BROWN / BLACK/ ///////////HORN HONK OU/////////////////GRAY(BEHIND RADIO) VIOLET/WHITE/ /////////////TACH IN//////////////////////////////BLUE W SILVER DOTS(BACK OF CLUSTER) DARK BLUE///////////////////STATUS OU////////////////////////NO CONNECTION PINK/WHITE/ //////////////////FLEX RELAY CONT////////////NO CONNECTION ORANGE / //////////////////////ACC OU////////////////////////////////NO CONNECTION PURPLE / ///////////////////////STARTER OU///////////////////////NO CONNECTION PINK//////////////////////////////IGNITION 1 OU     ////////////////////NO CONNECTION GREY////////////////////////////HOOD PIN IN BLUE/WHITE/ ////////////////2ND STATUS/REARDF OU////[REAR DEFOGGER]      BROWN / ///////////////////////BRAKE SHUTDOWN IN/////////GREEN / WHITE(BRAKESWITCH) BLACK/ WHITE/ /////////////NEUTRAL SAFETY IN////////////EMERGENCY BRAKE WIRE

did you see the diagnostic codes as to why it did not start?

make sure u have the nss wire connected and switch turned to on.

your start wires look correct to me.

Ted

2nd Year Tier 1 Medical School

Still installing as a hobby...pays for groceries

Compustar Expert

make sure the unit is still functioning.

take a meter, set to 20vdc, black to ground and red to purple start wire.

test to see if its giving a voltage when it cranks. if he does, you must have the green and purple wire reversed

remember, purple is going to the motor so it will go on the end of the wire going towards the fuse box.

Ted

2nd Year Tier 1 Medical School

Still installing as a hobby...pays for groceries

Compustar Expert

no code for no start, just the error tone on my remote. the nss switch is installed and in the on position. I'll have to test the voltage to see if this is the case. thanks for the input thus far

Alarm is in automatic mode, I'll try the chassis ground for the neutral safety wire. I'm going to also double check the heavy guage wiring. The alarm and lights and everything works, the only problem is when trying to start with the remote, parking lights and guage turns on but no start, then I get the error tone on the remote but no flashing parking lights indicating why it failed. I'm going to check those few things and then get back with you guys. I appreciate the help, glad to be a part of this community.

Okay so I've tested my connections and wire and fixed some errors, now I have two issues with the remote start. When I hit the remote start it starts for 2 secs then shutsdown, does this three times and then an error tone on my remote. Also when it begins to start when armed it triggers the alarm? Any ideas, should I use a better source for my tachometer wire than the back of the cluster, or does my alarm need to be programmed for voltage in the menu rather than tach?