Aloha,
I will be installing a Viper 5704v this weekend and I would like to have my connections looked over to make sure I have a good understanding of what wire goes where. I will be installing the remote start/alarm on a 2004 Chevrolet Express 1500. I have taken my time and researched the product but I do have some questions. I have seen several installs online use SPDT relays but they never really explain why they are using them and where at. Do I need a SPDT relay for my install? If so where at and what is the configuration for it? At the bottom I have listed the harness connections for the Viper 5704v with what I believe is the correct corresponding connection on the Express 1500. If I need relays or diodes somewhere, can someone please note it for me? I will also be using a XK09 XpressKit on D2D mode.
Thank you so much
Main Harness (H1), 6-pin connector
# Wire Color Description Connection
H1/1 RED (+)12VDC CONSTANT INPUT 12V Constant (RED / Black)
H1/2 BLACK (-) CHASSIS GROUND Good Ground
H1/3 BROWN (+) SIREN OUTPUT From Siren
H1/4 WHITE/ BROWN PARKING LIGHT ISOLATION WIRE - PIN 87a of onboard relay Not Used
H1/5 WHITE PARKING LIGHT OUTPUT ????? (Is this BROWN / white@BCM or Brown@fuse box under driver seat?)
H1/6 ORANGE (-) 500mA GROUND WHEN ARMED OUTPUT Not Used
H2 Harness, 24-pin connector
# Wire Color Description Connection
H2/1 PINK/WHITE (-) 200mA IGNITION/FLEX RELAY CONTROL OUTPUT Not Used
H2/2 BLACK/ WHITE (-) NEUTRAL SAFETY INPUT Ground with toggle switch
H2/3 BLUE/WHITE (-) 200mA 2ND STATUS /REAR DEFOGGER OUTPUT Not Used
H2/4 GREEN/ BLACK (-) 200mA OEM ALARM DISARM OUTPUT Not Used
H2/5 RED / WHITE (-) 200mA TRUNK RELEASE OUTPUT Not Used
H2/6 GREEN (-) DOOR TRIGGER INPUT (N/C* OR N/O) Tan, Lt Green, yellow/black @ BCM with diode isolate (Which way should the diode face?)
H2/7 BLACK / YELLOW (-) 200mA DOME LIGHT SUPERVISION OUTPUT Gray/Black@BCM (Requires a positive connection, do I need a relay to convert from neg to pos?)
H2/8 BROWN / BLACK (-) 200mA HORN HONK OUTPUT Tan@BCM
H2/9 DARK BLUE (-) 200mA STATUS OUTPUT Not Used
H2/10 PINK (-) 200mA IGNITION 1 OUTPUT Not Used
H2/11 WHITE/ BLACK (-) 200mA AUX 3 OUTPUT Not Used
H2/12 VIOLET (+) DOOR TRIGGER INPUT Not Used
H2/13 WHITE/ VIOLET (-) 200mA AUX 1 OUTPUT Not Used
H2/14 VIOLET/BLACK (-) 200mA AUX 2 OUTPUT Not Used
H2/15 ORANGE / BLACK (-) 200mA AUX 4 OUTPUT Not Used
H2/16 BROWN (+) BRAKE SHUTDOWN INPUT White@Brake Pedal
H2/17 GREY (-) HOOD PIN INPUT (N/C OR N/O) From Hood Pin
H2/18 VIOLET / YELLOW (-) 200mA STARTER OUTPUT ???? (What goes here?)
H2/19 BLUE (-) TRUNK PIN/ INSTANT TRIGGER INPUT (N/C OR N/O) Not Used
H2/20 GREY/BLACK (-) DIESEL WAIT TO START INPUT Not Used
H2/21 WHITE/ BLUE (-) REMOTE START/ TURBO TIMER ACTIVATION INPUT Not Used
H2/22 ORANGE (-) 200mA ACCESSORY OUTPUT Not Used
H2/23 VIOLET/WHITE TACHOMETER INPUT White or Purple@PCM
H2/24 GREEN / WHITE (-) 200mA OEM ALARM ARM OUTPUT Not Used
Remote Start, (H3) 10-pin connector
# Wire Color Description Connection
H3/1 PINK (+) IGNITION 1 INPUT/OUTPUT Ignition 1 (Pink)
H3/2 RED / WHITE (87) FLEX RELAY +12V INPUT (30A FUSED) 12V Constant (RED / Black)
H3/3 ORANGE (+) ACCESSORY OUTPUT Accessory (Orange)
H3/4 VIOLET (+) STARTER OUTPUT (CAR SIDE OF THE STARTER KILL) Starter (Yellow)
H3/5 GREEN (+) STARTER INPUT (KEY SIDE OF THE STARTER KILL) Starter (Yellow)
H3/6 RED IGNITION 1 +12V INPUT (30A FUSED) 12V Constant (RED / Black)
H3/7 PINK/WHITE (30) FLEX RELAY OUTPUT (car side of ign, acc or starter wire) Ignition 2 (White)
H3/8 PINK/BLACK (87a) FLEX RELAY INPUT (key side of ign, acc or starter wire) Not Used
H3/9 RED / BLACK ACCESSORY/STARTER RELAY +12V INPUT (30A FUSED) 12V Constant (RED / Black)
H3/10 NC No Connection
Door Lock, 3-pin connector
# Wire Color Description
1 BLUE (-) 500mA UNLOCK OUTPUT White@BCM
2 EMPTY NOT USED
3 GREEN (-) 500mA LOCK OUTPUT Light Blue@BCM
Mahalo...