'03 crv keyless trouble

Home / the12volt's Install Bay / Car Security and Convenience / '03 crv keyless trouble (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

linochan

Member - Posts: 5

Joined: November 15, 2003

Location: United States

Posted: April 23, 2004 at 5:43 PM / IP Logged

I have installed a alarm/ keyless entry onto my crv but i can't seem to figure out where the wires that lock and unlock the doors go. I have followed the wire diagram and the diagram for the alarm, but nothing seems to work. i was told to use diodes but i cant even get the keyless to do anything... if i plug the alarm in, if i leave the doors open, even if it is unarmed, it starts to beep and flash the lights, is that normal? i guess the question i have is really; on the alarm i have 6 different wires to hook up..... two say to hook up to the door lock switch.... one + and one -, and four are for the central locking ..... two hook up to the motor and the other two hook up to the actual central lock on the drivers side door,,,, or so it says... where do these really need to be because what it says on the unit and on the crv wire diagram,, i am confused.

dan

Sgam

mark mcj

Member - Posts: 19

Joined: April 13, 2004

Posted: April 23, 2004 at 11:09 PM / IP Logged

Go right to the switch. Get the meter out and test to output right at the connector to the drivers door switch harness.

I think it's neg. trgr, with the 03 I believe you have to go in the door to activate the locks.

mark mcj

linochan

Member - Posts: 5

Joined: November 15, 2003

Location: United States

Posted: April 24, 2004 at 3:56 AM / IP Logged

i have two wires coming out of the alarm, one is for door switch +, and the other is for door switch -. my car is a negative locking system. which do i use and how do i connect them to the two wires(lock and unlock) in my vehicle?

Sgam

JWorm

Platinum - Posts: 2,208

Joined: December 11, 2002

Location: New Hampshire, United States

Posted: April 24, 2004 at 7:11 AM / IP Logged

door switch + and - are for the wires that tell the domelight to turn on, not the wires that lock and unlock the door.

What system are you using? It sounds like the unit you have has built in door lock relays. If that is the case, two wires will get grounded, 2 won't be used, and 2 will go to the lock and unlock wire in the vehicle. If the unit doesn't have built in relays, you will connect the lock and unlock wires directly.

AutoObsessions

Member - Posts: 26

Joined: January 14, 2003

Location: United States

Posted: April 26, 2004 at 1:01 AM / IP Logged

The wires you are trying to use are the door pin wires. Those wires are used to tell the alarm that one of the doors has been opened. The crv has a negative door trigger and the door locks are negative also. So when u hook up that wire to the door lock wires it is triggering the alarm.

You must connect the - door switch wire to the domelight circuit. There are two wires this must be connected to so you must diode isolate the two. The factory alarm module is to the left of the steering column. There is a green plug in which the wires are coming out of. The drivers door pin is green and the rest of the doors are GREEN/ red.

Now on your alarm assuming that you have keyless entry outputs there should be a two or three wire plug for the keyless entry system. Usually there is a red and a green wire. One will be + lock and - unlock and one vice versa. These must be connected to the lock wires which are in the driver side kick panel. WHITE/ blue and WHITE/ green are the colors and they are in a gray plug right above the drivers kick.

Hope this helped

Search for other posts by AutoObsessions

linochan

Member - Posts: 5

Joined: November 15, 2003

Location: United States

Posted: April 26, 2004 at 4:46 PM / IP Logged

i have tried all of that already. i have checked everything with a multi meter and when i trigger the unlock on the alarm there is not a pulse on any wires that are meant for the door lock system. do you think that this feature is defective on my alarm?

Sgam

eurotech

Member - Posts: 44

Joined: April 26, 2004

Location: United States

Posted: April 26, 2004 at 6:24 PM / IP Logged

You wont get any output on the doorlock wires unless you ground the input wires (I am speculating that this alarm has internal relays) I'm not firmilliar with that exact alarm, therefore I dont know what colors to tell you to use, but generally the manual will explain wiring in terms of a relay. So for your input (which you are going to ground) use *87. Then for your outputs use *30.

I hope this helps...if not, how many lock/unlock wires are there? what are their colors?

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

'03 crv keyless trouble

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.