code alarm ca 120

Home / the12volt's Install Bay / Car Security and Convenience / code alarm ca 120 (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

Raul Puente

Member - Posts: 23

Joined: March 16, 2004

Location: United States

Posted: June 27, 2004 at 11:42 AM / IP Logged

this is my first time installing this alarm

what i was wondering is that coming from the

alarm there are six wires for the lock/unlock how would i go about

installing them on a basic car to unlock/lock the doors.

thanks

swamprat323

Gold - Posts: 1,335

Joined: September 22, 2002

Location: Florida, United States

Posted: June 27, 2004 at 12:01 PM / IP Logged

What kind of lock system do you have? What kind if car do you have?

swamprat323

Gold - Posts: 1,335

Joined: September 22, 2002

Location: Florida, United States

Posted: June 27, 2004 at 12:01 PM / IP Logged

Double post

Raul Puente

Member - Posts: 23

Joined: March 16, 2004

Location: United States

Posted: June 27, 2004 at 12:25 PM / IP Logged

the car is a pontiac grand am 2002

swamprat323

Gold - Posts: 1,335

Joined: September 22, 2002

Location: Florida, United States

Posted: June 27, 2004 at 1:14 PM / IP Logged

*2 Lock requires a negative trigger, and unlock requires a negative trigger through a 1,500 ohm resistor. Must use relays. Must close doors to lock with a single pulse.

Green with 1,500 ohm ressitor to lock/unlock wire.

Blue to lock/unlock wire

GREEN/ black to ground

Blue/Black to ground

Raul Puente

Member - Posts: 23

Joined: March 16, 2004

Location: United States

Posted: June 27, 2004 at 1:24 PM / IP Logged

ok what about the grn/red wire and the blue/red from the alarm

swamprat323

Gold - Posts: 1,335

Joined: September 22, 2002

Location: Florida, United States

Posted: June 27, 2004 at 1:28 PM / IP Logged

They wont be used. You may have to have the door closed b4 it will lock, not sure on a 2002 but it that way for a 2003

Raul Puente

Member - Posts: 23

Joined: March 16, 2004

Location: United States

Posted: June 27, 2004 at 1:38 PM / IP Logged

what are those wires mainly used for are they for changing the polarity from pos; to neg;

or the other way around.

swamprat323

Gold - Posts: 1,335

Joined: September 22, 2002

Location: Florida, United States

Posted: June 27, 2004 at 1:39 PM / IP Logged

Sorry about this but made a mistake use the

GREEN/ red to ground

blue/red to ground

Dont use GREEN/ black and blue/black

Raul Puente

Member - Posts: 23

Joined: March 16, 2004

Location: United States

Posted: June 27, 2004 at 1:46 PM / IP Logged

so what your say is that to get pos conncet those wires to 12volts

and to get neg conncet to ground also what are those wires grn/blk

and blu/blk used for?

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.