trailblazer w/o 457G

Home / the12volt's Install Bay / Car Security and Convenience / trailblazer w/o 457G (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

mxxmikexx

Silver - Posts: 796

Joined: September 18, 2002

Location: United States

Posted: February 04, 2006 at 5:15 PM / IP Logged

I've never installed a remote starter w/o keyless entry which obviously requires the 457, however i have a customer who only wants remote start, my question is will there be any issues with factory security besides the pk2 to contend with if i dont use a 457g?

au5599

Copper - Posts: 94

Joined: December 22, 2005

Location: United States

Posted: February 05, 2006 at 4:00 PM / IP Logged

just do the passlock II interface. If it has a factory alarm it will honk ohrn once when it goes to start. Factory alarm thinks someone is stealing it then it gets everything it needs so it shuts down thinking someone is in it with key starting it.

To test lock door after rolling down driver window. Walk away for a few minutes. Then reach in and open door from inside. If horn goes off then it has a factory alarm. So just warn then it will honk horn when starting cause it is shutting down factory alarm.

subconceptz

Member - Posts: 31

Joined: January 02, 2006

Location: United States

Posted: February 05, 2006 at 9:52 PM / IP Logged

Also sometimes without doing the remote locks on the aftermarket unit, the factory remote keyless entry will not work while the car is running off the aftermarket remote start. The customer may have to shut the remote start down to use the factory keyless. Some vechicles, depending on vechicle programming, is set up to shut down the factory keyless entry system when the ignition is powered up.

JWorm

Platinum - Posts: 2,208

Joined: December 11, 2002

Location: New Hampshire, United States

Posted: February 06, 2006 at 1:17 AM / IP Logged

subconceptz wrote:

GM factory remotes never shut down when the vehicle is on. Nothing to worry about here.

If you hook up the disarm wire from the remote start to the disarm wire in the drivers door the horn won't honk when remote starting.

au5599

Copper - Posts: 94

Joined: December 22, 2005

Location: United States

Posted: February 06, 2006 at 1:55 PM / IP Logged

JWorm wrote:

If you hook up the disarm wire from the remote start to the disarm wire in the drivers door the horn won't honk when remote starting.

But who wants to yank a door panel if you dont have too.

JWorm

Platinum - Posts: 2,208

Joined: December 11, 2002

Location: New Hampshire, United States

Posted: February 06, 2006 at 2:51 PM / IP Logged

au5599 wrote:

JWorm wrote:

If you hook up the disarm wire from the remote start to the disarm wire in the drivers door the horn won't honk when remote starting.

But who wants to yank a door panel if you dont have too.

Personally, if it has the factory alarm the customer doesn't have the option of not getting doorlocks. The module that does doorlocks and passlock cost me $5 more than the module that just does Passlock. That $5 is not worth the time it takes to go into the door.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

trailblazer w/o 457G

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.