double pulse unlock

Home / the12volt's Install Bay / Car Security and Convenience / double pulse unlock (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

muaiad97

Copper - Posts: 207

Joined: April 08, 2003

Location: Canada

Posted: October 05, 2007 at 11:00 PM / IP Logged

hi all

i am working on dodge caravan 2000 with remot starter CT-3400 TW the unlock need double pulse to unlock the doors the lock working fine its programing issue that what the instalation manual says but i tried every thing still not unlocking its timing pule not set any one worked in ths kind of remot starter please .

thanx

KarTuneMan

Platinum - Posts: 7,056

This member has made a donation to the12volt.com. Click here for more info.

This member consistently provides reliable information

Joined: December 14, 2004

Location: Isle Of Man

Posted: October 05, 2007 at 11:50 PM / IP Logged

LOCK

WHITE/ lt.green or WHITE/ red

In driver's kick or BCM

The Body Control Module (BCM) is located behind the fusebox under the driver's side of the dash, against the firewall. These wires are located in the plug on the left side. A negative pulse through a 1500 ohm resistor will lock the doors and a negative pulse through a 250 ohm resistor will unlock the doors. If the vehicle is equipped with a factory alarm, substitute a 4020 ohm resistor to arm/lock the doors and a 665 ohm resistor to disarm/unlock the doors. Relays should be used, see the DOORLOCK diagram.

UNLOCK

WHITE/ lt.green or WHITE/ red

In driver's kick or BCM

muaiad97

Copper - Posts: 207

Joined: April 08, 2003

Location: Canada

Posted: October 06, 2007 at 9:30 AM / IP Logged

hi again

yes i did that but what i am saying it need double puls to unlock everything is conected and every thing works perfect exept the the unlock need to give more secand to activated its programing issue becaus when i attach the unlock wire to ground it works but with the remote dosnt .

KarTuneMan

Platinum - Posts: 7,056

Joined: December 14, 2004

Location: Isle Of Man

Posted: October 06, 2007 at 9:39 AM / IP Logged

Yes .... the double pulse IS a programming issue. Somehwere in the programming menu should be instructions on how to set up double pulse. BUT.... it's poss. that your unit will not do "double pulse"

moonliter

Copper - Posts: 322

Joined: February 28, 2007

Location: Canada

Posted: October 06, 2007 at 12:04 PM / IP Logged

muaiad97 wrote:

hi again

did you set your unlock opt on mode 1 function 4 on 'opt 3' which is 1 lock pulse and 2 unlock pulses ?

muaiad97

Copper - Posts: 207

Joined: April 08, 2003

Location: Canada

Posted: October 07, 2007 at 12:36 PM / IP Logged

thankx again for reply yes i did go to menue and mode 1 and function 4 and push unlock to increese the pulses time still nothing the time for out put unlock its to short .

moonliter

Copper - Posts: 322

Joined: February 28, 2007

Location: Canada

Posted: October 07, 2007 at 1:28 PM / IP Logged

did you use relay with resistor for your unlock or just the unlock wire with resistor from your rs ?

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

double pulse unlock

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.