508d and 504 problems on a python 990

Home / the12volt's Install Bay / Car Security and Convenience / 508d and 504 problems on a python 990 (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

poorkid

Member - Posts: 8

Joined: June 12, 2007

Location: United States

Posted: December 12, 2007 at 1:48 PM / IP Logged

508d and 504 problems on a Python 990. I installed this yesterday in my 1990 300zx. lol everything seems to work correctly minus the sensors. I installed 2- 504 shock sensors "Y" tied the red and black (seperately) then both green and blue to the blue lead (sensor 1) and green on sensor 2 so no diodes were nedded. I ran a 507 (tilt sensor) dioded with my (-) door trigger, I also put a diode on the door trigger. then ran a 508D proximity sensor to the blue mulitplexed trigger H1/7.

My problem is the proximity sensor doesn't always set off the alarm and I can't seem to adjust the zone range. also my shock sensors don't respond well it takes a door slam to set it off. please help me figure this out.

poorkid

Member - Posts: 8

Joined: June 12, 2007

Location: United States

Posted: December 13, 2007 at 8:17 PM / IP Logged

I just encounterd more problems. My alarm will set off at random in my drive way?? I have no trees or anything that could set off the 508 and the weather has been fine.

poorkid

Member - Posts: 8

Joined: June 12, 2007

Location: United States

Posted: December 13, 2007 at 9:27 PM / IP Logged

ok so my remote says the trunk sensor is setting off my alarm.. I didn't connect the trunk trigger wth!

poorkid

Member - Posts: 8

Joined: June 12, 2007

Location: United States

Posted: December 13, 2007 at 11:14 PM / IP Logged

lol k I mis read the install manual i wired my 508 proximity sensor to the multiplexed trunk trigger. I still can't figure out the adjustment for it or why my 504 dual shock sensors aren't very sensitive. also is there a way to turn off the LED light while the system is unarmed its pretty annoying at night.

poorkid

Member - Posts: 8

Joined: June 12, 2007

Location: United States

Posted: December 14, 2007 at 4:49 PM / IP Logged

OK So let me rewrite this. Maybe people will better understand so I can get some help.

I'm having problems with the 508d and 2- 504 sensors on a Python 990. I installed this yesterday in my 1990 300zx. lol everything seems to work correctly minus the sensors. I installed 2- 504 shock sensors "Y" tied off one plug. combined the reds then combined the blacks. then combined the green and blue wires to the blue lead (sensor 1) and combined the green and blue to the green lead (sensor 2) so no diodes were needed.

I ran the 508D proximity sensor to the blue mulitplexed trunk trigger H1/7 by combining the green and blue and used a chassis ground along with a constant 12v.

My problem is the proximity sensor doesn't always set off the alarm. The LEDs on the sensor light up but the alarm doesn't warm or set off so I can't even adjust the zone range. also my shock sensors don't respond well it takes a door slam to set it off. I have 1- 504 sensor double side taped to the floor under the dash and the other 504 sensor (wires extended) by the rear shock tower.

My alarm falses alot and and when I set the alarm then wait 15+ seconds then disarm it I get 3 chirps, the resonder remote displays that sensor 1, impact, and my 508 proximity all were set off. I have since unplugged the 508 prox and my remote and alarm still display the same thing.

Also Is there a way to stop the blinking blue LED while the system is unarmed? Its very annoying while driving at night.

please help me figure this out.

Thanks Jeremy

poorkid

Member - Posts: 8

Joined: June 12, 2007

Location: United States

Posted: December 17, 2007 at 1:45 PM / IP Logged

Well I figured everything out minus the prox sensor. Thanks to the people at www.caraudio.com. I did't use the remote start feature since my car is manual so I didn't have the 12v ignition source connected from that harness.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

508d and 504 problems on a python 990

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.