2006 Pontiac G6 Remote Start Wiring

need wiring diagram for a bulldog rs82 remote car starter for a pontiac 2006 g6 thanksMichael Dziekonski

PONTIAC G6 MODEL      YEAR(S G6      2005-2007 KEY      T-HARNESS      IMMOBILIZER N/A      N/A      PONTIAC'S MULTIPLEX IGNITION/TRANSPONDER SYSTEM, See NOTE #1 PART      COLOR      LOCATION      DIAGRAM 12 VOLT CONSTANT      RED/BLACK (+)      BCM, RED 41-PIN PLUG, PIN D1, "C3"       STARTER      See NOTE #1            STARTER 2      N/A            IGNITION 1      PINK (+)      IGNITION SWITCH, GREEN 6-PIN PLUG       IGNITION 2      N/A            IGNITION 3      N/A            ACCESSORY/HEATER BLOWER 1      BROWN (+)      IGNITION SWITCH, GREEN 6-PIN PLUG       ACCESSORY/HEATER BLOWER 2      N/A            KEYSENSE      N/A            PARKING LIGHTS ( - )      BROWN/WHITE (-)      @ HEADLIGHT SWITCH or BCM C2, PIN 5, See NOTE #2       PARKING LIGHTS ( + )      BROWN (+)      @ HEADLIGHT SWITCH or BCM, C3, PIN A7, See NOTE #2       POWER LOCK      WHITE (1-Wire System) See NOTE #5      @ BCM, C1, Pin 66, See NOTE #2 POWER UNLOCK      Same wire LOCK MOTOR WIRE      GRAY/BLACK to GRAY (+)      @ BCM, C3, Pin A5, See NOTE #2       DOOR TRIGGER      See NOTE #3      @ BCM, C1, See NOTE #2 DOMELIGHT SUPERVISION      GRAY (-)      @ BCM, C3, Pin A10, See NOTE #2       TRUNK RELEASE      BROWN/WHITE (-)      @ BCM, C1, PIN 71, See NOTE #2       SLIDING POWER DOOR      N/A            HORN      TAN (-)      @ BCM, C2, PIN 14, See NOTE #2       TACH      See NOTE #4      @ IGNITION CONTROL MODULE       WAIT TO START LIGHT      N/A            BRAKE      WHITE (+)      @ BCM, C1, PIN 24, See NOTE #2       FACTORY ALARM DISARM      LT.GREEN ( - ) NEG . THRU 500OHMS (use a 470 + 33 ohm 1/2watt connected end to end)      DOOR HARNESS IN DRIVERS KICK OR @ BCM,C1, PIN 35, See NOTE #2       ANTI-THEFT      PONTIAC'S MULTIPLEX IGNITION/TRANSPONDER, See NOTE #1            NOTES NOTE #1: THIS VEHICLE REQUIRES A SPECIAL INTERFACE BYPASS MODULE TO REMOTE START, PART # DBALL2 or XK09 THESE INTERFACES WILL ALSO DO THE KEYLESS ENTRY, ignition delay circuit is needed when installing an RS82, RS1100, or RS1200 and a DBALL2 or XK09 interface in a GM vehicle that has no starter/ crank wire coming from the ignition switch. NOTE #2: the BCM (Body Control Module) is part of the FUSE/RELAY BOX , on the FRONT PASSENGER SIDE of the CENTER CONSOLE, the connectors are: C1-72pin GRAY Plug, C2-72pin GRAY Plug, C3-41pin RED Plug, and C4-68pin LIGHT GRAY Plug. NOTE #3: the DRIVERS DOOR is a GRAY/BLACK (-) PIN 51, the PASSENGER DOOR is a TAN/WHITE (-) PIN 72, the DRIVERS REAR DOOR is a LIGHT BLUE/BLACK (-) PIN 54 and the PASSENGER REAR DOOR is a LIGHT GREEN/BLACK (-) PIN 53. When connecting to an ALARM SYSTEM, use all (4) DOOR TRIGGER wires and DIODE ISOLATE NOTE #4: on the 2.2L engine, use the WHITE or ORANGE wire, on the 3.5L 6-Cylinder engine, use the PURPLE, ORANGE/WHITE or LIGHT BLUE. NOTE #5: this vehicle uses a 1-Wire DOOR LOCKING SYSTEM that requires a (-)Negative thru a 1500 Ohm Resistor to UNLOCK and a straight (-)Negative to LOCK, some units will also require (2) extra relays~wirewise~ Verify all wiring with your meter before making any connections!