2005 Dodge Wiring Diagrams

I need the wiring diagrams for any 2005 Dodge vehicles. I'm starting to do back up sensors, dvd's, and navigation installs on new dodge vehicles. Thanks guys!

Any is too broad. A specific one I might be able to help you.Be careful whose advice you buy, but be patient with those who supply it.

2005 Grand Caravan w/ rear air. Also Magnum. Thanks!

DIRECTWIRE™ WIRING INFORMATION - DODGE / CARAVAN / 2005 / Remote Start [PRINT THIS PAGE] 12volts lt. blue/red (10A)   +   ignition harness Starter yellow   +   ignition harness Second Starter PURPLE / brown   -   ignition harness Notes: The second starter wire is negative trigger thru a 180 ohm resistor. MUST use a relay. Refer to DirectFax document 1083 for wiring information. Ignition pink/white   +   ignition harness Second Ignition N/A        Third Ignition N/A        Accessory not required for remote start        Second Accessory N/A        Keysense N/A        Power Lock PURPLE / dk. green   -   BCM, white plug, pin 21 Notes: Lock is negative trigger thru a 5.3K ohm resistor. Unlock is negative trigger thru a 2.0K ohm resistor. MUST use relays. The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Can also use Directed 456L interface modules. Power Unlock same as power lock wire        Lock Motor tan/white   5wi BCM, green plug, pin 10 Notes: The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Unlock Motor tan/lt. green   5wi BCM, green plug, pin 28 Notes: The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Parking Lights+ WHITE/ brn (L), WHITE/ org (R)   +   driver kick, harness to rear Parking Lights- WHITE/ brown   -   switch or BCM, gray plug, pin 21 Notes: The parking lights are negative trigger thru a 2.1K ohm resistor. There is a rest resistance on the wire, so MUST use a relay to isolate away from the switch. See DirectFax document 1082 for wiring information. The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Hazards WHITE/ dk. blue   -   switch or BCM, gray plug, pin 31 Notes: The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Turn Signal(L) wht/lt blu (F), wht/dk grn (R) +   BCM, green plug, pins 1, 2 Notes: The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Turn Signal(R) WHITE/ tan (F), WHITE/ brown (R) +   BCM, green plug, pins 3, 4 Notes: The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Reverse Light WHITE/ lt. green   +   BCM, green plug, pin 9 Notes: The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Door Trigger see notes   -   BCM, white plug Notes: The driver door trigger is purple in pin 6, the passenger door is PURPLE / white in pin 7, the left sliding door is PURPLE / gray in pin 8, and the right sliding door is purple / YELLOW in pin 5. Use all four wires and diode isolate each. Also have to diode isolate from the BCM. Refer to DirectFax document 1076 for wiring information. The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Dome Supervision yellow/brown or yellow/white   +   BCM, white plug, pin 33 Notes: The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Trunk/Hatch Pin PURPLE / orange   -   BCM, white plug, pin 29 Notes: A diode must be placed inline on this wire to avoid problems with the dome lights and parking lights. The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Hood Pin PURPLE / lt. blue (export model) -   BCM, white plug, pin 30 Notes: The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Trunk/Hatch Release PURPLE / tan   -   BCM, green plug, pin 6 Notes: Hatch release is negative trigger thru a 1.69K ohm resistor. MUST use a relay. The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Power Sliding Door PURPLE / dk. blue   -   BCM, white plug, pin 1 Notes: Left power sliding door is negative trigger thru a 1.5K ohm resistor. Right power sliding door is negative trigger thru a 2.7K ohm resistor. MUST use relays. The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Factory Alarm Arm arms on lock with door open        Factory Alarm Disarm factory remote only        Disarm No Unlock with ignition and Sentry Key        Tachometer NOT BROWN / white   ac   ign coil pack or any fuel injector Wait to start N/A        Brake Wire WHITE/ tan   +   brake pedal switch Parking Brake dk. GREEN / WHITE   -   parking brake switch Horn Trigger dk. GREEN/ purple   -   steering column Memory Seat 1 PURPLE / brown   -   BCM, green plug, pin 24 Notes: Memory seat 1 is negative trigger thru a 6.8K ohm resistor. Memory seat 2 is negative trigger thru a 2.1K ohm resistor. MUST use relays. The BCM (Body Control Module) is in the driver kick panel near the parking brake. It has 5 plugs in it, one 6 pin plug and four 34 pin plugs. Memory Seat 2 same as memory seat 1 wire   -      Memory Seat 3 N/A   -      Immobilizer Bypass Module: Required: Yes Type: Sentry Key Part #: 556C, 556U, or 555U Notes: Standard on SXT models. Optional on SE models.        This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter. Directed electronics, Inc. assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information. DIRECTWIRE™ WIRING INFORMATION - DODGE / MAGNUM / 2005 / Remote Start [PRINT THIS PAGE] 12volts lt. blue/red (15A)   +   ignition harness Starter pink/dk. green   +   ignition harness Second Starter PURPLE / brown   -   ignition harness Notes: The second starter wire is negative trigger thru an 180 ohm resistor. MUST use a relay. Refer to DirectFax document 1084 for wiring information. Ignition pink/white   +   ignition harness Second Ignition           Third Ignition           Accessory same as second starter wire   -   ignition harness Notes: The accessory wire is negative trigger thru a 610 ohm resistor. MUST use a relay. Refer to DirectFax document 1084 for wiring information. Second Accessory           Keysense           Power Lock PURPLE / dk. green   -   DKP or cluster, gry 26P plug, pin 5 Notes: Lock is negative trigger thru a 330 ohm resistor. Unlock is negative trigger thru a 100 ohm resistor. MUST use relays. Power Unlock same as power lock wire        Lock Motor lt. green   5wi DKP or cluster, gry 26P plug, pin 12 Unlock Motor tan/lt. green   5wi DKP or cluster, gry 26P plug, pin 11 Parking Lights+ WHITE/ purple   +   pass. kick, brn 26 pin plug, pin 26 Parking Lights- WHITE/ brown   -   sw or cluster, gry 26P plug, pin 3 Notes: Parking lights are negative trigger thru an 1,670 ohm resistor. There is a rest resistance on the wire, so must use a relay to isolate from the switch. Hazards WHITE/ dk. blue   -   hazard switch Turn Signal(L) use hazards wire        Turn Signal(R) use hazards wire        Reverse Light WHITE/ lt. green   +   pass. kick, brn 26 pin plug, pin 17 Door Trigger see notes   -   each kick or instrument cluster Notes: The LF door is purple in the white plug, pin 3. The RF door is PURPLE / white in the white plug, pin 3. The LR door is PURPLE / gray in the gray 26 pin plug, pin 10. The RR door is purple / YELLOW in the gray 26 pin plug, pin 9. Use all four wires and diode isolate each. Dome Supervision yellow/white   +   instrument cluster, wht plug, pin 12 Notes: Also found in the passenger side A pillar. Trunk/Hatch Pin PURPLE / orange   -   PKP or cluster, gry 26P plug, pin 23 Hood Pin PURPLE / lt. blue (export only)   -   pin switch under hood Trunk/Hatch Release PURPLE / tan   -   PKP or cluster, gry 26P plug, pin 22 Notes: The hatch release is negative trigger thru a 4,700 ohm resistor. MUST use a relay. This wire will meter when you use the release handle on the rear hatch. Power Sliding Door N/A        Factory Alarm Arm arms on lock with door open        Factory Alarm Disarm factory remote only        Disarm No Unlock with ignition and Sentry Key        Tachometer NOT BROWN / yellow   ac   any ignition coil or fuel injector Wait to start N/A        Brake Wire dk. GREEN / WHITE   +   brake pedal switch Parking Brake gray/black   -   sw or cluster, gry 26P plug, pin 18 Horn Trigger dk. GREEN/ orange   +   horns under hood Memory Seat 1 PURPLE / brown   -   memory switch in driver door Notes: Memory seats are negative trigger thru resistors. The resistor values are not known at this time. Cut the wire and meter the values as you press the memory 1 and memory 2 buttons. Memory Seat 2 same wire as memory seat 1   -      Memory Seat 3 N/A   -      Immobilizer Bypass Module: Required: Yes Type: Sentry Key Part #: 556C, 556U, or 555U Notes: Standard on all models.        This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter. Directed electronics, Inc. assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information. Be careful whose advice you buy, but be patient with those who supply it.