the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2007 Honda Element - Viper 4806V install


Post ReplyPost New Topic
< Prev Topic Next Topic >
savagem 
Member - Posts: 9
Member spacespace
Joined: January 08, 2017
Location: Ontario, Canada
Posted: January 13, 2017 at 8:05 AM / IP Logged Link to Post Post Reply Quote savagem
kreg357 wrote:
Still have the wrong 6 Pin Main connector. Only difference is noted below :
H/3 BROWN (-) 200mA HORN HONK OUTPUT
This wire goes to the vehicles' Orange (-) horn wire.
Perhaps a typo. ACC2 is WHITE/ Red
VIPER 4806V - 8 Pin White Remote Start Heavy Gauge Connector       
Pin01 - RED / Black - (+) FUSED 12V ACCESSORY/STARTER INPUT     White @ IGNITION SWITCH HARNESS
Pin02 - Pink/Black - (+) FLEX RELAY INPUT FLEX RELAY          NOT USED - PINOUT WIRE
Pin03 - Pink/White - (+) IGNITION 2 / FLEX RELAY OUTPUT       WHITE/ Red @ IGNITION SWITCH HARNESS   *set Flex to ACC2
Pin04 - Red - (+) FUSED 12V IGNITION 1 INPUT   White @ Ignition Harness
Pin05 - Violet - (+) STARTER OUTPUT            BLACK/ White @ Ignition Harness
Pin06 - Orange - (+) ACCESSORY OUTPUT          BLACK/ Red @Ignition Harness
Pin07 - RED / White - (+) FUSED 12V IGNITION 2 / FLEX RELAY     White @ IGNITION SWITCH HARNESS
Pin08 - Pink - (+) IGNITION 1 INPUT/OUTPUT     BLACK / YELLOW @ Ignition Harness
Just to confirm that:
1) Pin04 - Red - (+) FUSED 12V IGNITION 1 INPUT
2) Pin07 - RED / White - (+) FUSED 12V IGNITION 2 / FLEX RELAY
Are both connected to the White 12V Constant White wire at the ignition? Do I join all 3 wire before the connection to the vehicle.
I'll make the correction to my sheet. I had Pin 04 to BLACK / YELLOW.
kreg357 
Platinum - Posts: 7,802
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: Pennsylvania, United States
Posted: January 13, 2017 at 8:51 AM / IP Logged Link to Post Post Reply Quote kreg357
Due to the current, I would try to run all 3 thick fused Viper wires to the Element's White Power wire and make 3 connections there. Another possible way is to join the thick Red and the thinner Red about 3 inches from the White connection and then make one solder connection there. Same for the RED / White and RED / Black, join them 3 inches from the White wire and then just one connection to the White wire. Leave the fuses in place.
Soldering is fun!
Page of 2

If you wish to post a reply to this topic, you must first login.
If you are not already registered, you must first register.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer