the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

ultrastart 2256m


Post ReplyPost New Topic
< Prev Topic Next Topic >
jmacf14 
Copper - Posts: 160
Copper spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: December 27, 2005
Location: United States
Posted: January 14, 2007 at 7:22 PM / IP Logged  

I have a poser for anyone familiar with these alarms. I have installed almost 40 of these in the past  3 years, and have never had this problem, thus I think it might be a warranty issue. Here is the problem; I installed this unit saturday, and all of my connections are correct, and soldered. The unit worked perfect on 5 start attempts for testing, everything worked great untill I tried to adjust the shock sensor. With this unit, you have to depress the lock and unlock buttons for 3 seconds. the siren chirps, the park lights flash 3 times and then stay on. then you strike the a pillar with the palm of your hand 3 times to set. the alarm chirps each time it detects the impact. well when I depressed the 2 buttons, nothing happened. So I tried again still nothing, but the doors locked and the alarm armed. then the alarm would not recognize the remotes any more. I couldnt unlock with the remotes. as soon as I unlocked with the key and opened the door the alarm sounded. I ended up having to disconnect the siren while I tried to reprogram the remotes. after a while the alarm would go through the remote reprogram mode but would not recognize the remotes! I am at a loss. Anyone else ever have this problem? 

jmacf14
jmacf14 
Copper - Posts: 160
Copper spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: December 27, 2005
Location: United States
Posted: January 15, 2007 at 5:21 PM / IP Logged  
 Anyone? Hoping someone out there has encountered this before.
jmacf14
splaudio 
Copper - Posts: 237
Copper spacespace
Joined: January 22, 2006
Posted: January 16, 2007 at 4:07 PM / IP Logged  

what i would do is unplug then replug in the brain, do this with the antenna too.  to program the remotes turn the ignition on-off,on-off,on then press the antenna button 1 time then hold til the horn honks 5 times while holding the antenna button press lock on the 1st remote, then press lock on the 2nd remote release the antenna button. it will beep when u push the lock button on each remote telling u it is programed.

to me it sounds like u have a bad antenna connection,pinched antenna wire or bad antenna...

jmacf14 
Copper - Posts: 160
Copper spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: December 27, 2005
Location: United States
Posted: January 16, 2007 at 6:40 PM / IP Logged  
 Thanks for the reply. I tried disconnecting everything and reconnecting. Like I said though every thing was working great then out of the blue, nothing but alarm sounding. No response to remotes. The leds in the antennae are working and I can get the alarm to go through the sequence to learn the remotes, it just doesnt respond to them, not even to relearn them. I am open to more suggestions, and thanks again for the reply.
jmacf14
customak47 
Copper - Posts: 164
Copper spacespace
Joined: October 25, 2005
Location: Vanuatu
Posted: January 17, 2007 at 8:07 AM / IP Logged  
I have done a bunch of the manual units and i have never ran into the problem you are describing. It sounds like a bad module to me. Try swapping and let me know cause I have had a very small handful of units (auto trans mostly) that were bad out of box, though not the same symptoms.
My rifle is my friend...
xtremej 
Gold - Posts: 1,440
Gold spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: February 24, 2006
Location: United States
Posted: January 17, 2007 at 9:25 AM / IP Logged  
I haven't seen the troubles you describe,we did have one that would remote start whenever it wanted. I would try swapping out the brain also and see how she goes, also double check all connnections and make sure you have a good body ground for the remote start.
splaudio 
Copper - Posts: 237
Copper spacespace
Joined: January 22, 2006
Posted: January 17, 2007 at 7:14 PM / IP Logged  
contact Terry Thomson head tech guy at ultra he will tell ya it has something to do with ur antenna.  if ya want email me SPLaudiuo78@hotmail.com  and i will give ya his email.  i have not done a manual tranny remote start just something i refuse to do.
jmacf14 
Copper - Posts: 160
Copper spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: December 27, 2005
Location: United States
Posted: January 24, 2007 at 7:47 PM / IP Logged  
 Well I ended up replacing the brain and that fixed the problem. All is well now. Must be a fluke. Something definately went wrong in that one. Thanks for the replys guys.
jmacf14

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer