the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

08 dodge nitro wiring


Post ReplyPost New Topic
< Prev Topic Next Topic >
martinrp 
Member - Posts: 2
Member spacespace
Joined: May 12, 2004
Location: United States
Posted: September 22, 2009 at 2:44 PM / IP Logged  
I will be installing a remote start in a 2008 Dodge Nitro.  Does anyone have a diagram for this vehicle.  Thanks
rpm
tommy... 
Gold - Posts: 1,901
Gold spacespace
Joined: December 10, 2004
Location: United States
Posted: September 25, 2009 at 10:39 PM / IP Logged  
BatteryBLUE/RED(+)IGNITION SWITCH HARNESS...THIS WIRE ONLY SUPPLYS 10 AMPS OF CURRENT, FOR HIGH CURRENT APPLICATION GO DIRECTLY TO THE BATTERY08 dodge nitro wiring - Last Post -- posted image.
08 dodge nitro wiring - Last Post -- posted image.Ignition 1PINK/WHITE(+)IGNITION SWITCH HARNESS
08 dodge nitro wiring - Last Post -- posted image.Accessory 1VIOLET/BROWN(-)IGNITION SWITCH HARNESS...THIS WIRE IS ALSO THE KEYSENSE AND SECOND STARTER WIRE, USE A 580 OHM RESISTOR FOR SECOND ACCESSORY, FOR REMOTE START INFORMATION08 dodge nitro wiring - Last Post -- posted image.
08 dodge nitro wiring - Last Post -- posted image.Accessory 2PINK / YELLOW(+)IGNITION SWITCH HARNESS...NOT ON ALL MODELS08 dodge nitro wiring - Last Post -- posted image.
08 dodge nitro wiring - Last Post -- posted image.Starter 1YELLOW/GRAY(+)UNDER HOOD AT MODULE ON DRIVERS FENDER...NOT FOR REMOTE START*08 dodge nitro wiring - Last Post -- posted image.
08 dodge nitro wiring - Last Post -- posted image.Starter 2VIOLET/BROWN(-)IGNITION SWITCH HARNESS...THIS WIRE IS ALSO THE KEY SENSE AND ACCESSORY WIRE, USE A 180 OHM RESISTOR FOR SECOND START FOR REMOTE START INFORMATION08 dodge nitro wiring - Last Post -- posted image.
08 dodge nitro wiring - Last Post -- posted image.Anti-Theft TypeSENTRY KEY® VEHICLE IMMOBILIZER
08 dodge nitro wiring - Last Post -- posted image.Anti-Theft DescriptTHE KEY SENDS AN RF SIGNAL TO THE BCM MODULE THROUGH AN ANTENNA LOCATED AROUND THE IGNITION CYLINDER
08 dodge nitro wiring - Last Post -- posted image.Key SenseVIOLET/BROWN(-)IGNITION SWITCH HARNESS...THIS IS THE SAME WIRE AS THE SECOND STARTER AND THE ACCESSORY WIRE, USE A 8500 OHM RESISTOR FOR KEY SENSE, FOR REMOTE START INFORMATION08 dodge nitro wiring - Last Post -- posted image.
08 dodge nitro wiring - Last Post -- posted image.Speed SenseDARK GREEN/ BROWN(AC)AT PCM MODULE ON PASSENGER FENDER UNDER HOOD
08 dodge nitro wiring - Last Post -- posted image.Parking LightsWHITE/ VIOLET(+)IN HARNESS IN DRIVER KICKPANEL
08 dodge nitro wiring - Last Post -- posted image.Brake LightsWHITE/ TAN(+)AT SWITCH ABOVE BRAKE PEDAL...ALSO WHITE/ DARK GREEN IN HARNESS IN DRIVER KICKPANEL08 dodge nitro wiring - Last Post -- posted image.
08 dodge nitro wiring - Last Post -- posted image.Reverse LightsWHITE/ LIGHT GREEN(+)IN HARNESS IN DRIVER KICKPANEL...ALSO AT MODULE UNDER HOOD ON DRIVER FENDER08 dodge nitro wiring - Last Post -- posted image.
08 dodge nitro wiring - Last Post -- posted image.HornDARK GREEN/ VIOLET(-)IN HARNESS AT STEERING COLUMN

Power UnlockVIOLET/DARK GREEN(-)IN HARNESS IN DRIVER KICKPANEL TO DOOR...UNLOCK IS (-) THROUGH A 100 OHM RESISTOR, SAME WIRE FOR LOCK, MUST USE RELAYS08 dodge nitro wiring - Last Post -- posted image.
08 dodge nitro wiring - Last Post -- posted image.PowerLockVIOLET/DARK GREEN(-)IN HARNESS IN DRIVER KICKPANEL TO DOOR...LOCK IS (-) THROUGH A 330 OHM RESISTOR, SAME WIRE FOR UNLOCK

M.E.C.P & First-Class
Go slow and drink lots of water...Procrastinators' Unite...Tomorrow!
kickergod 
Member - Posts: 21
Member spacespace
Joined: September 19, 2009
Location: New York, United States
Posted: September 26, 2009 at 2:03 PM / IP Logged  
I have done a few of these now. I use a bypass for the resistor values and key bypass and a 1 button remote starter since locks are in the key and work while the vehicle is running. Your main power will be in a large harness in the driver kick panel with your brake and park light wires. Power is heavy gauge I believe Black or Red off hand. Bypass wires and ignition at the ignition plug. Accessory not needed and bypass takes care of the rest up there. Horn will honk funny unless you get it at the relay under the hood so don't bother.  Just a tach, hood pin, and ground and your done (technically ground should be first).
Ryan Edwards
MECP Certified Installer

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Sunday, April 28, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer