This is my first remote start alarm install, and my first post on this forum. I have gathered a lot of information from this forum already that has tremendously helped me out with my install, but unfortunately i am stuck on this issue i am now having and cant seem to find an answer.
After installing the alarm everything seemed to work just fine except the remote start. The parking light flashed 7 times indicating it was still in manual mode. So i tried to re-program the unit for an automatic transmission and while in the process i think i did it wrong and put the system in some kind of weird mode. I cant get it to go into any mode now except valet on/off. If i hold down the program button on the control panel after turning the ign to on/off with door open it doesn't do anything after holding it down even for over a few minutes. Unless it is, but the unit just isn't chirping/siren like it did the first time (it chirps if i arm/disarm or panic). I have been looking for any type of information that could help me out, but haven't come up with much. I tried resetting the unit through the steps shown in the manual, but that requires going through the programming which i cant get into. Ever disconnected my battery, and back up battery for a few hrs and that didn't help since the unit has everything stored in memory.
I thought maybe the system was not recognizing the door was open, but then again it was responding the first time, and i would assume if it wasn't recognizing the door open then i should have issues when i arm the system. I even tried opening different doors, or both driver and passenger doors and it didn't do anything. The first initial time going into programming my driver/passenger doors were open.
Process used for programming automatic:
1 ) turn car to ignition then off.
2) hold valet button until it chirps 3 times
3)Release valet push once release and then push and hold . On remote hit lock , it will chirp 2xs .
3) turn car to ignition then off and it should remote start
Vehicle: 2011 Toyota Tacoma Automatic
Alarm: Viper 5704v
Accessories: 506T Audio Sensor, 520T Backup battery, 507M Tilt sensor, X2 530T Window Automation System (530T not installed yet)
Remote start bypass: Directed Electronics Inc PKALL Xpress Kit Data Transponder
Wiring diagram used:
Sorry about format i copied it off the install guide i made.
Viper 5704 Install on 2011 Toyota Tacoma DCSB TRD Sport
Main Harness (H1), 6-pin connector from alarm to Tacoma
1: H1/1 RED (+) 12VDC CONSTANT INPUT
•12 VOLT CONSTANT WHITE/ RED (+) @ IGNITION SWITCH, (WHITE, 8-Pin Plug) Pin 5
2: H1/2 BLACK (-) CHASSIS GROUND
•Find strong ground point
3: H1/3 BROWN (+) SIREN OUTPUT
•Connect to siren included with alarm.
4: H1/5 WHITE PARKING LIGHT OUTPUT
•PARKING LIGHTS (+) GREEN (+) @ DASH FUSE BOX, (WHITE, 13-Pin Plug (D) Pin 10
5: H1/6 ORANGE (-) 500mA GROUND WHEN ARMED OUTPUT
•Connect to accessories for alarm to ground when alarm is armed.
H2 Harness, 24-pin connector from alarm to Tacoma
1: H2/4 GREEN/ BLACK (-) 200mA OEM ALARM DISARM OUTPUT
•FACTORY ALARM DISARM GREEN/ BLACK (-) (Requires Double Pulse), NOTE #2 in DRIVERS KICK PANEL, (WHITE, 10-Pin Plug) Pin 8
2: H2/6 GREEN (-) DOOR TRIGGER INPUT (N/C* OR N/O)
•DOOR TRIGGER GREEN/ YELLOW (-)@ DASH FUSE BOX, (WHITE, 18-Pin Plug (F) Pin 7
3: H2/8 BROWN / BLACK (-) 200mA HORN HONK OUTPUT
•HORN GREEN/ RED (-) @ DASH FUSE BOX, (WHITE, 18-Pin Plug(C) Pin 10
4: H2/16 BROWN (+) BRAKE SHUTDOWN INPUT
•BRAKE BLUE (+) @ DASH FUSE BOX, (WHITE, 13-Pin Plug (D) Pin 13
5: H2/17 GREY (-) HOOD PIN INPUT (N/C OR N/O)
•Connect to hood pin included with alarm.
6: H2/18 VIOLET / YELLOW (-) 200mA STARTER OUTPUT
•Use later with relay for remote star.
7: H2/23 VIOLET/WHITE TACHOMETER INPUT
•TACH BLACK/ WHITE (AC) @ DATA LINK Connector, (WHITE, 16-Pin Plug) Pin 9
Door Lock, 3-pin connector
1: BLUE (-) 500mA UNLOCK OUTPUT
•POWER UNLOCK GRAY (TYPE B) in DRIVERS KICK PANEL, (WHITE, 10-Pin Plug) Pin 7
2: GREEN (-) 500mA LOCK OUTPUT
•POWER LOCK BLUE/WHITE (TYPE B) in DRIVERS KICK PANEL, (WHITE, 10-Pin Plug) Pin 6
Remote Start, (H3) 10-pin connector
connect H3-2, H3-6, H3-9 and H1-1 to +12V constant.
1:H3/1 PINK (+) IGNITION 1 INPUT/OUTPUT
•IGNITION 1 BLACK/ RED (+) @ IGNITION SWITCH, (WHITE, 8-Pin Plug) Pin 6
2: H3/2 RED / WHITE (87) FLEX RELAY +12V INPUT (30A FUSED)
•12v Constant
3: H3/3 ORANGE (+) ACCESSORY OUTPUT
•ACCESSORY /HEATER BLOWER 1 WHITE/ GREEN (+) @ IGNITION SWITCH, (WHITE, 8-Pin Plug) Pin 2
4: H3/4 VIOLET (+) STARTER OUTPUT (CAR SIDE OF THE STARTER KILL)
•STARTER 1 GREEN/ BLACK (+) @ IGNITION SWITCH, (WHITE, 8-Pin Plug) Pin 7
5: H3/5 GREEN (+) STARTER INPUT (KEY SIDE OF THE STARTER KILL)
•Not used.
6: H3/6 RED IGNITION 1 +12V INPUT (30A FUSED)
•12v Constant
7: H3/7 PINK/WHITE (30) FLEX RELAY OUTPUT (car side of ign, acc or starter wire)
Connect H3-7 to Ignition2. Factory default programming sets this output as IGN2.
•IGNITION 2 BLUE / YELLOW (+) @ IGNITION SWITCH, (WHITE, 8-Pin Plug) Pin 1
8: H3/8 not used
9: H3/9 RED / BLACK ACCESSORY/STARTER RELAY +12V INPUT (30A FUSED)
•12v constant.
PKALL Blue/White goes to Viper H2/9
Use pictures above for all H3 harness install.
Window Wiring Diagram
LF window up –Blue
LF window down-Blue/Black
RF Window up-Blue / YELLOW
RF Window Down-Black
LR Window up-GREEN / WHITE
LR Window Down-GREEN/ Red
RR Window Up-GREEN/ Black
RR Window Down-Green
Some sources used for install:
http://www.commandocaralarms.com/wiring/2009-2012/toyota/tacoma/2041.html
https://www.the12volt.com/installbay/forum_posts.asp~TID~130004
https://www.the12volt.com/installbay/forum_posts.asp~TID~132417
http://www.tacomaworld.com/forum/audio-video/252032-how-install-viper-5704-alarm-remote-start.html