Viper 4806v on toyota camry with key override

HI Friends I am going to install Viper 4806V on toyota camry 2007 with fortin key override all bypass module. I am figuring out the connections, before i open and start putting connections. I have few questions: 1. What is toyota camry 07 light flash polarity, as need to set jumper on 4806v 2. Bypass module need ground input while remote starter running on...where to get from 4806v...it has only 500mA ground output when armed... 3. ignition1(+) in/out and ign1 +12vdc input wires...how to connect to ign1 wire 4. ignition2(+) out and ign2 +12vdc input wires...how to connect to ign2 wires 5. ihave only one starter output(+) where as car had two..starter 1(+) nd starter2(+) 6. where is light flash relay in camry 07, as need to connect to 87a and 30 on that relay 7. Trunck release is +-reverse on camry 07 , where as remote start has (-) 200mA trunk release output...can i connect them 8. camry 07 factory horn polarity, as need to set jumper on 4806v 9. where to connect (-)200 mA ign1 output to car wire 10. where to connect (-)200mA starter output to car wire thnx in advance Regds..Litt

1) White at H1 Viper to headlight switch, white 20 pin plug pin 18 black. Set fuse on Viper as NEG (-). 2) Dark blue H2 "status wire (= GWR) perfectly adequate. 3) Connect pink at H3 to yellow Pink/white at H3 to pink Orange at H3 to white Cut blue starter wire, green to key side and violet to starter motor side. Violet / YELLOW at H2 to relay 4 pin 85, ignition wire connected to Viper pink to 86 12V+ constant 30 amps fused to 87 30 to grey, second starter. Diode across 86 and 85, 1N4004, band to 86. All above, IGN switch loom. 6) Not needed see no.1 unless you mean auto lights. 7) Trunk release, cut black wire and use a 5 pin relay, motor side 30, switch side 87a. RED / white Viper H2 to 85 12V+ constant fused at 20 amps to 87 and 86 Diode 1N4004 across 85 and 86, band to 86. 8) Horn switch white to black, steering column loom, NEG (-) 9 and 10 already explained 200mA ign wires not required starter 200mA shown above.

Thnx howie for prompt reply - Viper 4806 has 6pin main harnedd H1 - RED -+12VDC CONSTANT INPUT H2 - BLACK - CHASIS GROUND H3 - BROWN - HORN HONK OUTPUT H4 - WHITE/ BROWN LIGHT FLAS ISOLATION WIRE-PIN 87A OF LIGHT FLASJ RELAY H5 - WHITE PIN 30 OF LIGHT FLASH RELAY H6 - GROUND WHEN ARMED OUTPUT m little confused, see this is main harness regds.. Regds..Litt

Because they are actually labelled H1/1, H1/2 etc! H1 above refers to the above. H2 refers to the low current aux such as tach, aux outputs, door triggers, trunk release. H3 refers to the high current input and output wires, remember to connect up red, re/black and RED / white to a 12Volt constant.

Hi howie First of all thnx for taking your time..i really appreciate. 8) Horn switch white to black, steering column loom, NEG (-) DIDNT understand as4806v has either Brown (-) 200mA Horn Honk Output at 6 pin harness (H1 as per you) OR Blue ...   .factory Horn Input at 24 Pin harness (H3 as per you) Also as per wire color, Horn wire is White wire on black connector beside air bag connector. pls advise me how to connect horn wires... Regds..Litt

Use the brown on H1 and join the blue H2 not H3 to your brown set jumper to NEG. The problem is they've changed their designations! H1 = Main harness, 6 pin H2 = Aux/shutdown H3 = Remote start 8 pin. I also said cut starter 1, don't this unit doesn't have a starter cut built in requires an off board relay so no green, just join your violet at H3 to blue at ignition switch.

Hi howie Thnx again for taking your time and effort to help me. Use the brown on H1 and join the blue H2 not H3 to your brown -DO I have to join brown from h1 and blue on h2 ONLY or -I have to connect these both to white on black Connector Beside Air Bag Connector. please confirm thnx, i think i will be able to do it after this. I will post all the notes and video once i am done, so that somebody else can do it easily. Regds..Litt

Both.I think.

Hi howie I am installing today, little confused I have Pink at H3 connected to Yellow on ignition connector & Pin 86 on relay pin 85 on relay connected to voilet yelow on h2 starter output pin 30 connected to grey on ignition connector and constant +12volt to pin 87 pls confirm if i am ok regds..LittRegds..Litt

That's correct.