the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2000 Dodge Neon Factory Alarm Problems


Post ReplyPost New Topic
< Prev Topic Next Topic >
jc18750 
Copper - Posts: 113
Copper spacespace
Joined: July 21, 2004
Location: United States
Posted: September 04, 2005 at 1:51 PM / IP Logged  
So i've been installing alarms for about 4 years now and this one is making me angry. I am putting it on a 2000 Dodge Neon Highline with power windows, locks, and a stock security system. I have put the alarm on, hooked up the keyless entry, remote start, hooked up the imobilizer bypass module (556U), everything on the alarm that i hooked up works great.
But here's the kicker. The factory alarm comes on when I lock the car with the alarm that i installed. but when i unlock the car with my remote. The doors unlock, but the factory alarm stays on. So you open the door and the horn goes off.
I wired the locks through the light green wire above the kick panel, as described. i use a neg trigger through a 1.5 ohm to unlock it, and a neg trigger through a 270 ohm to lock it.
Here comes the good part. ---
   When i lock it through the 270 ohm resistor using the neg straight from the alarm, the doors lock and the stock alarm comes on. if i use the 270 ohm resistor through a relay and draw the source ground from the chassy, the doors lock but the factory alarm stays off.
But no matter what i do, i cannot get the factory alarm to turn off with the locks. When i use no resistor, relay or not, the car locks and the factory alarm comes on. The owner doesn't care if the factory alarm works or not, but i don't know where it is.
So i either need to disable/remove the factory alarm, or figure out how to effectively disarm the factory system during unlock. Thanks for your input.
iskidoo 
Silver - Posts: 1,043
Silver spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: December 08, 2002
Location: Maine, United States
Posted: September 04, 2005 at 7:36 PM / IP Logged  
Are you double pulsing the unlock wire? You will need to. Also your unlock with factory security should be through a 7500 ohm resister not a 250 ohm resistor. The lock should be through a 2700 ohm resistor not a 1000 ohm resistor. The 1000 & 250 ohm resistors are for the Neons without factory security.
Steve G
jc18750 
Copper - Posts: 113
Copper spacespace
Joined: July 21, 2004
Location: United States
Posted: September 04, 2005 at 7:44 PM / IP Logged  
Thanks, I'll give that a try tonight, and let you know how it goes.
jc18750 
Copper - Posts: 113
Copper spacespace
Joined: July 21, 2004
Location: United States
Posted: September 05, 2005 at 7:51 PM / IP Logged  
Works perfectly. case closed.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer