the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2008 grand caravan remote start


Post ReplyPost New Topic
< Prev Topic Next Topic >
audiomaninc 
Copper - Posts: 108
Copper spacespace
Joined: April 18, 2007
Location: United States
Posted: December 18, 2007 at 7:11 PM / IP Logged  

Hey there!  I'm going to attempt a starter in a 2008 Grand Caravan tomorrow, using an Omega Mars11, and an Omega IM06 transponder bypass with SICH1 0.02 firmware.  Has anyone attempted one of these vehicles yet?  The manual for the bypass tells me to take apart a module at the ignition barrel and solder wires directly to the board.  I'm just looking for some advice before I jump in.  Thanks!

-Jason @AudioMan

techman93 
Silver - Posts: 591
Silver spacespace
Joined: October 28, 2006
Location: Pennsylvania, United States
Posted: December 18, 2007 at 7:52 PM / IP Logged  
Test to see if you need a bypass first because you may not need it. It will have a second starter multiplex that you will need to isolate through a relay and 180 ohm resistor. If you need diagram let me know.
The wire I'm test'n isn't doin' what it's supposed to be doin'... I am so glad I printed that tech sheet, with the wrong info.
Do it right the first time... or I might have to fix it for ya
tonyberg 
Copper - Posts: 116
Copper spacespace
Joined: November 08, 2005
Location: North Dakota, United States
Posted: December 18, 2007 at 7:56 PM / IP Logged  
eh the 08 caravan is a whole new ball of wax bud...its easy..just follow that diagram that comes with the SICH firmware...be careful soldering on the board....there are no resistors in an 08
audiomaninc 
Copper - Posts: 108
Copper spacespace
Joined: April 18, 2007
Location: United States
Posted: December 19, 2007 at 5:39 PM / IP Logged  

Got it installed today, but a few issues.  Followed SICH diagram, everything connected inside ignition baril.  When RS is activated, there's a ding, like the key is in the ignition, but none of the lights on the dashboard turn on, or the accessories.  Double checked everything is still intact inside the ign. Also, can't find the brake wire, or parking lights.  The only tech sheet I have is from Code Alarm, and it's pretty sparse to say the least.  Please help!

Jason

techman93 
Silver - Posts: 591
Silver spacespace
Joined: October 28, 2006
Location: Pennsylvania, United States
Posted: December 19, 2007 at 6:46 PM / IP Logged  
Battery         LIGHT BLUE/RED     (+)     IGNITION SWITCH HARNESS     
Ignition 1 PINK/WHITE          (+)     IGNITION SWITCH HARNESS     
Parking Lights     WHITE/ LIGHT GREEN (L) & WHITE/ TAN (R)     (+)          AT TIPM MODULE ON DRIVERS SIDE OF ENGINE     
Brake Lights     WHITE/ TAN     (+)     AT SWITCH ABOVE BRAKE PEDAL     
Horn          DARK GREEN/ VIOLET     (-)     IN HARNESS AT STEERING COLUMN
Power Unlock     VIOLET/DARK GREEN     (-)     IN HARNESS TO DRIVER DOOR IN DRIVER KICKPANEL     
PowerLock     VIOLET/DARK GREEN     (-)     IN HARNESS TO DRIVER DOOR IN DRIVER KICKPANEL
this per audiovox site
no other notes on it
The wire I'm test'n isn't doin' what it's supposed to be doin'... I am so glad I printed that tech sheet, with the wrong info.
Do it right the first time... or I might have to fix it for ya
racing_bidule 
Copper - Posts: 66
Copper spacespace
Joined: December 13, 2007
Location: Quebec, Canada
Posted: December 19, 2007 at 7:40 PM / IP Logged  

This vehicle takes less then 1:30h using an iDataLink module. It takes care of everything, why would you use the hard way with these vehicles. The iDataLink module is taking care of the whole ignition cycle (the way the ignition is cycled is critical on these vehicles) the bypasskit relies on the remote starter ignition cycle which will not work wit every remote starters.

starts at page 13

http://www.idatalink.com/store/viewDoc.php?id=79

If you fail on your first attempt, at least destroy all evidence you tried!
tonyberg 
Copper - Posts: 116
Copper spacespace
Joined: November 08, 2005
Location: North Dakota, United States
Posted: February 22, 2008 at 7:59 PM / IP Logged  
We just switched over to the ADS-AL-CA module as the main one that we stock, and I must say its great.  We utilized one today on a 2008 Grand Caravan SXT.  The only thing I disagree with is taking apart the wireless ignition module.   They state in the directions that if you solder onto the pins underneath the cover that you will not be able to separate the circuit boards....but there is absolutely no need to ever separate the circuit boards, these modules are not serviceable and can only be ordered as whole pieces.   My recommendation is to solder to the pins that you can see when you remove the access panel.   
Velocity Motors 
Moderator - Posts: 12,488
Moderator spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Fabrication. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: March 08, 2002
Location: Manitoba, Canada
Posted: February 23, 2008 at 8:53 AM / IP Logged  
tonyberg wrote:
We just switched over to the ADS-AL-CA module as the main one that we stock, and I must say its great. We utilized one today on a 2008 Grand Caravan SXT. The only thing I disagree with is taking apart the wireless ignition module.   They state in the directions that if you solder onto the pins underneath the cover that you will not be able to separate the circuit boards....but there is absolutely no need to ever separate the circuit boards, these modules are not serviceable and can only be ordered as whole pieces.   My recommendation is to solder to the pins that you can see when you remove the access panel.   
I have not had the opportunity to install into a new Caravan yet, do you have pics of what you are talking about ? Thanks
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer