the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

remote start on 1999 f150


Post ReplyPost New Topic
< Prev Topic Next Topic >
saxron 
Member - Posts: 4
Member spacespace
Joined: November 19, 2014
Location: Pennsylvania, United States
Posted: November 25, 2014 at 9:16 PM / IP Logged  
I am installing a avital 4103 remote starter and a PKALL immobilizer override on a 1999 f150 4.6L
I wired it up and it cranks and will start the vehicle when the key is in the ignition and in the run position. With out the key it will only crank with the remote start. This truck has 3 ignition wires and the remote start only has 1 ignition wire hook up. I think I need to wire in a relay but i'm not sure how to do it. Also do I need 2 relays so all 3 ignition wires are activated ? My other question is which ignition wire to hook the PKALL to?
Also the PKALL requires a (-) while running (status) hook up to the remote start, I used the H1/4 White /blue wire on the remote start which says it is a (-) input set to 1 activation pulse.
I have installed 3 other remote starters but they had better instructions than the Avital. And I know Direct electronics only gives tech support to dealers.
I appreciate any HELP !!
saxron
davep. 
Gold - Posts: 644
Gold spacespace
Joined: May 27, 2011
Location: California, United States
Posted: November 25, 2014 at 9:41 PM / IP Logged  
Use the 4-pin satellite harness for the following:
Blue 2nd Status output = to PKALL ground when running (-) input. The wht/blu that you used is an activation input. Won't work for the PKALL, and you don't need it. Tape off the blu/wht.
Use the pink wire for a third IGN. Pink is a (-) trigger. Use a relay:
86 and 30 = Hot at all times. (Fused)
85 = pink pin 4 of satellite output.
87 = to 3rd Ignition.
Fix the PKALL GWA input first. That may be all you need.
You may not need to do anything further with the IGN circuits. The gry/yel does stuff that isn't necessary to power in an unoccupied vehicle. Airbags, trailer charge relay, electric shift T-case. The Lt blu / pink shows for anti lock brakes, and nothing else. Don't need that one either for RS. Power the RED / blk, and dk blu / lt green as IGN 1 & 2, and blk/lt green as ACCY and that should do it until key take-over.
I hear you on the instructions not being clear. All DEI instructions suffer from clunky translations to English from either Mandarin or Japanese, I'm not sure which.
saxron 
Member - Posts: 4
Member spacespace
Joined: November 19, 2014
Location: Pennsylvania, United States
Posted: November 27, 2014 at 10:10 AM / IP Logged  
Thanks for getting back to me I work retail so now all I need is a day off to try it again!
saxron

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer