rs/al problems 2007.5 ram 2500

Long time reader, first time poster. I have been installing car audio and security for nearly 10 years. I am trying to install an excalibur 1850 in my personal Ram 2500 Diesel (Automatic). I got the IDatalink and have it flashed to DS-AL(DL)-CH5. I have the Idata and the excalibur hooked up together. I have tried both D2D and W2W modes of install and with either option I can not get the truck to start. The locks, horn, lights all work great, but the truck will not start. When the start is activated the truck turns on, the ac comes on, but the truck never makes any attempt to start. The only wires that I have going to the truck are the positive wires from the alarm (direct to the battery), the MUX, CANH, CANL, 12V and Ignition from the Idata. I also have the Start from the alarm connected to the start input on the Idata. Any ideas would be appreciated.

Did you tie into the MUX, CAN High, & CAN Low at the immobilizer connector? I tied into the MUX at the ignition switch connector and it caused me to have starting issues via remote start. Also, is your diesel timer set up? If so, maybe the timer hasn't timed out to allow the remote start to crank?I drink current, eat ohms, and bleed voltage

Thanks for the reply the time is set to zero currently and I have tested to make sure that the Excalibur is engaging at the same time as the idata. I connected to can high and low where they are twisted together in the steering column when I tried to connect the mux at the ignition it caused the truck to not start at all even with the key. I am not sure where the immobilizer is.

While I have used the ADS CH5 firmware many times, I have not done a diesel truck yet.  Excalibur is not my

normal brand, so I am not familiar with them.  I will offer a few thoughts with those disclaimers...

I always go with W2W mode.  Always works. 

With W2W mode, you should do a Factory Reset on the bypass module then select Standard Install Mode

( two blinks ) and lock it in.  Then program the bypass module to the truck.

After a quick Lock / Unlock test the next step should be a R/S Tach Learn.

I would use a standard 15 second Diesel Delay.

Double check to ensure the 1N4001 diode in the Ignition wire circuit is oriented correctly ( band towards the

R/S ).

While the colors are slightly different, the pin locations are the same on the Jeep Patriot Pictorial I posted

a while ago.  https://www.the12volt.com/installbay/forum_posts.asp?tid=130393  Follow the Type 3 wiringshown in the ADS CH5 guide.  Other than +12V power, Chassis Ground, Parking Lights and the Hood Pin, no other R/S to vehicle connections are needed.

There is a photo of the Transponder plug at the ignition switch in the Pictorial.

Soldering is fun!

If you look at the diagram on idatalink's website the immobolizer is attached to the ignition switch. It has a 8-pin connector. Here is the diagram if you dont have it. Your CAN H and CAN L are fine if the idatalink programmed and the keyless functions work.I drink current, eat ohms, and bleed voltage

Thanks for all the help so far. I have reconnected the CANH, CANL, MUX, 12V, and Ignition. I have pictures to show where everything is connected. When I connect the MUX wire to the same location as the others, the truck will not start even with the key and the idata behaves as if it has no power. When I connect the MUX where it is in the photos, everything will come on, but it will never try to start. I can see all of the status lights come and go on the dash, the ac turns on, but it never even attempts to start. The locks are working fine, but no remote start. I have changed the modes to delayed start by 15 seconds and this produced no change. I have made sure that the alarm was set to automatic transmission and that all the connects appear to be correct. Any help would be appreciated the yellow wire going to the harness is the MUX wire from the idata, going to the purple and brown wire the CANL, CANH, 12V, and Ignition all connected at what appears to be the immobilizer. And for the record the electrical tape is temporary, I used temporary connections to test everything before taking the time to solder.

Strange.  Kinda looks like a 2006 ignition setup.  You might see if the ADS CH5 Type 2 wiring diagram is more

accurate for your truck and use that diagram for the install.  Those older vehicles had a separate Starter (+) wire.  Here is a link to a 2006 RAM 1500 install with an iDatalink CH5 bypass module : https://www.the12volt.com/installbay/forum_posts.asp?tid=130085

Fortin lists the 2006 and 2007 models as the same, while iDatalink does not.  Here is a link to their EVO-ALL install

guide for comparison :  http://fortin.ca/download/9681/evo-all_chrysler_dodge_jeep_(skreem%2B_no_t-harness).rev-20130605.pdf

Soldering is fun!

Thanks for the suggestion but I have checked the harness where the positive starter should be and there is no wire there.

Can you get a better photo of the SKREEM transponder connector?  It should be an 8 Pin connector, with Pin 8 empty.  Here is a photo of one from a 2011 Compass that also uses the CH5 firmware :

Soldering is fun!

Below is a better pic of the harness. It would make sense to me to hook up the mux here with the other wires, but when it is hooked up the idata becomes completely unresponsive, I can't even reset it, also the ignition stops working all together.