the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2nd ignition wire be used as accessorry?


Post ReplyPost New Topic
< Prev Topic Next Topic >
jim hunter 
Silver - Posts: 351
Silver spacespace
Joined: March 23, 2006
Location: United States
Posted: December 29, 2009 at 8:47 PM / IP Logged  
on audiovox if you look in the instructions it will tell you under programming menu ign2 on during crank, or same as starter1, same as acc, it is programmable just hook it to your 2nd acc wire and change programming to make it an accessory
tommy... 
Gold - Posts: 1,901
Gold spacespace
Joined: December 10, 2004
Location: United States
Posted: December 29, 2009 at 8:48 PM / IP Logged  

1. RF Programmable Features:

Feature Selection 1 Flash 2 Flash 3 Flash 4 Flash Default

1 Run Time 5 Min. 10 Min. 15 Min. 20 Min. 10 Min.

2 Ign. 2 During Crank Off -On-(default) On

3 Light Output During Run Steady Flash Steady

M.E.C.P & First-Class
Go slow and drink lots of water...Procrastinators' Unite...Tomorrow!
legenux 
Copper - Posts: 92
Copper spacespace
Joined: July 30, 2005
Location: United States
Posted: December 29, 2009 at 9:03 PM / IP Logged  
tommy... wrote:

PINK/WHITE Wire: Ignition 2 Output

Connect this wire to the ignition 2 wire from the ignition switch. This wire will show + 12 volts when the ignition

key is turned to the "ON" or "RUN" position and is some cases the "START" or CRANK" position. This wire

will show 0 volts when the key is turned to the "OFF" and "ACCESSORY" positions.

NOTE: See programming information concerning this wire to allow output during the "START" mode.

Don't think there's a pink/white wire for the APS 901. I believe green is the ignition 2 wire. I still don't see why cannot connect alarm's ignition 2nd(unused) to car's 2nd accessory(required) directly? In theory should work correct?
legenux 
Copper - Posts: 92
Copper spacespace
Joined: July 30, 2005
Location: United States
Posted: December 29, 2009 at 9:08 PM / IP Logged  
tommy... wrote:
1. RF Programmable Features:
Feature Selection 1 Flash 2 Flash 3 Flash 4 Flash Default
1 Run Time 5 Min. 10 Min. 15 Min. 20 Min. 10 Min.
2 Ign. 2 During Crank Off -On-(default) On
3 Light Output During Run Steady Flash Steady
I never program an audiovox before. Will give it go tomorrow. So I want it to be OFF for Ign. 2 During Crank correct? Thanks all for help.
Chris Luongo 
Platinum - Posts: 3,746
Platinum spaceThis member consistently provides reliable informationspace
Joined: May 21, 2002
Location: Massachusetts, United States
Posted: December 29, 2009 at 9:20 PM / IP Logged  
If it were a Code Alarm branded piece, the associated would be pink/white as Tommy was mentioning.
With the Prestige and Pursuit brands, it's a thick green wire as you described.
And yes, go into the second bank of featuers, where you have your runtime, tach/voltage and all those settings, and set Ignition 2 to "off during crank," and it will behave just like the purple accessory output.
What kind of car is this going into, anyway?
legenux 
Copper - Posts: 92
Copper spacespace
Joined: July 30, 2005
Location: United States
Posted: December 29, 2009 at 9:43 PM / IP Logged  
Chris Luongo wrote:
If it were a Code Alarm branded piece, the associated would be pink/white as Tommy was mentioning.
With the Prestige and Pursuit brands, it's a thick green wire as you described.
And yes, go into the second bank of featuers, where you have your runtime, tach/voltage and all those settings, and set Ignition 2 to "off during crank," and it will behave just like the purple accessory output.
What kind of car is this going into, anyway?
03 Murano. Everything is working, except the 2nd accessory - thus no heat =(
legenux 
Copper - Posts: 92
Copper spacespace
Joined: July 30, 2005
Location: United States
Posted: December 29, 2009 at 9:45 PM / IP Logged  
Many thanks guys. Your expertise help me once more. Will try to program the thing tomomrrow. Hopefully smooth sailing for a @ home installer.
tommy... 
Gold - Posts: 1,901
Gold spacespace
Joined: December 10, 2004
Location: United States
Posted: December 29, 2009 at 10:15 PM / IP Logged  
legenux wrote:
tommy... wrote:

PINK/WHITE Wire: Ignition 2 Output

Connect this wire to the ignition 2 wire from the ignition switch. This wire will show + 12 volts when the ignition

key is turned to the "ON" or "RUN" position and is some cases the "START" or CRANK" position. This wire

will show 0 volts when the key is turned to the "OFF" and "ACCESSORY" positions.

NOTE: See programming information concerning this wire to allow output during the "START" mode.

Don't think there's a pink/white wire for the APS 901. I believe green is the ignition 2 wire. I still don't see why cannot connect alarm's ignition 2nd(unused) to car's 2nd accessory(required) directly? In theory should work correct?

I mentioned in an earlier post the difference... Ignition stays powered up during crank...Accessory does not...It drops voltage...Just to clear that up for ya...!

M.E.C.P & First-Class
Go slow and drink lots of water...Procrastinators' Unite...Tomorrow!
legenux 
Copper - Posts: 92
Copper spacespace
Joined: July 30, 2005
Location: United States
Posted: December 30, 2009 at 1:00 PM / IP Logged  
Works like a charm after programming it. Pretty easy too. Thanks all =)
Page of 2

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer