the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

05 murano w/ intellikey keysense wire


Post ReplyPost New Topic
< Prev Topic Next Topic >
big d z 
Member - Posts: 33
Member spacespace
Joined: November 29, 2007
Location: Texas, United States
Posted: December 21, 2010 at 11:45 AM / IP Logged  
I'm trying to locate the keysense wire on an 05 Murano with intelligent key. I need the valet keysense wire so I can trigger it when using the 556 bypass.
Thanks.
Mike M2 
Platinum - Posts: 2,652
Platinum spacespace
Joined: June 29, 2005
Location: United States
Posted: December 21, 2010 at 5:19 PM / IP Logged  

BLACK/ red at the igntion switch, or pin 37 at the BCM.

Mike M2
Tech Manager
CS Dealer Services
big d z 
Member - Posts: 33
Member spacespace
Joined: November 29, 2007
Location: Texas, United States
Posted: December 21, 2010 at 11:49 PM / IP Logged  
Mike M2 wrote:

BLACK/ red at the igntion switch, or pin 37 at the BCM.

Ok, I think I found it. I found a BLACK/ red wire on a grey connector, that connects to something around the ignition. I tested this wire, and when I insert a valet key into the ignition (and remove my hand) this wire goes to 12V.
So I connected the second accessory wire to this and verified that when I start the RS, this line goes to 12V just before cranking.
But the result is the same as before. The car cranks for a couple seconds but doesn't start. If I insert the key into the ignition and try the RS it cranks and then starts.
So what else could I be missing? Perhaps its how I have the 556u antenna ring wrapped around the ignition cylinder? This cylinder is hard to place the ring on cause it has this plastic ring topped off by a lighted ring that lights green when key is turned.
Any ideas?
big d z 
Member - Posts: 33
Member spacespace
Joined: November 29, 2007
Location: Texas, United States
Posted: December 22, 2010 at 12:19 AM / IP Logged  
Well, sure enough, it was the placement of the 556 ring. Wow, talk about a pain in the ass. Man, in my 05 Titan it was easy, but in the Murano, I had to trim a groove on the back side of the lighted collar for the 556 ring to fit into so that I can squeeze the ring around the outside of what is probably the key sensing mechanism and in under this lighted ring.
After that, BAM!, starts right up, and the red key light is no longer on.
Now, onto the final problem. Powering up the keysense with the second accessory output like this keeps the keysense on constant 12V. So, anyone can jump into the car and turn the ignition and drive away without a key.
So the question now is whats the best way to only power this keysense long enough for RS to start the car and then shut the keysense back off?

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer