the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

viper 5706v,dball2, 2010 tacoma


Post ReplyPost New Topic
< Prev Topic Next Topic >
helidave 
Member - Posts: 10
Member spacespace
Joined: January 30, 2014
Posted: February 04, 2014 at 5:11 PM / IP Logged  
Getting ready to install a Viper 5706V and DBALL2 in a 2010 Tacoma, AT, dot-key.
Will the DBALL2 do anthing besides immobilizer bypass in this vehicle?
What I really want to know is if using the DBALL2 will change the wiring required for the 5706 (door locks, brake pedal, tach, etc)
Here are the functions the DBALL2 can perform in a 2010 Tacoma according to xpresskit.com:
D2D
PK-Immobilizer Bypass-Data No Key Req'd
ST-Brake Status (foot brake)
ST-Hand Brake Status
ST-Hand Brake Status
ST-Ignition Status
helidave 
Member - Posts: 10
Member spacespace
Joined: January 30, 2014
Posted: February 04, 2014 at 7:46 PM / IP Logged  
If someone can double check my connections I would appreciate it.
viper 5706v,dball2, 2010 tacoma - Last Post -- posted image.viper 5706v,dball2, 2010 tacoma - Last Post -- posted image.
freqsounds 
Copper - Posts: 289
Copper spacespace
Joined: October 17, 2008
Location: Virginia, United States
Posted: February 04, 2014 at 8:20 PM / IP Logged  
helidave wrote:
Getting ready to install a Viper 5706V and DBALL2 in a 2010 Tacoma, AT, dot-key.
Will the DBALL2 do anthing besides immobilizer bypass in this vehicle?
What I really want to know is if using the DBALL2 will change the wiring required for the 5706 (door locks, brake pedal, tach, etc)
Here are the functions the DBALL2 can perform in a 2010 Tacoma according to xpresskit.com:
D2D
PK-Immobilizer Bypass-Data No Key Req'd
ST-Brake Status (foot brake)
ST-Hand Brake Status
ST-Hand Brake Status
ST-Ignition Status
The DBALL will eliminate all those wires. Hook up the HSCAN wires and the RX/TX wires to the immobilizer and you're good to go.
All these power, status, triggers, etc. are communicated over the HSCAN. It's like a network.
Just make sure the DBALL is updated to the latest firmware via the XKLoader2. Read the entire manual for the DBALL and you should be good to go!
No question is stupid or not worth asking. You were once a noob, right? :)
helidave 
Member - Posts: 10
Member spacespace
Joined: January 30, 2014
Posted: February 04, 2014 at 9:15 PM / IP Logged  
freqsounds wrote:
The DBALL will eliminate all those wires. Hook up the HSCAN wires and the RX/TX wires to the immobilizer and you're good to go.
All these power, status, triggers, etc. are communicated over the HSCAN. It's like a network.
Could you be more specific about which wires I can leave off the alarm? It looks like it can do a lot, but for my vehicle it will only send brake, handbrake, and ignition status to the alarm/rs.
viper 5706v,dball2, 2010 tacoma - Last Post -- posted image.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer