Wiring power to LandRover Dscy

Home / the12volt's Install Bay / General Discussion / Wiring power to LandRover Dscy (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

palbert

Member - Posts: 4

Joined: May 03, 2004

Location: United States

Posted: May 03, 2004 at 9:34 PM / IP Logged

I have the basics about power and grounding, but don't know where to wire power (red) to. Any suggestions from the experts? Where do I connect? Fuse box or where?

Thx.

boomer_106

Silver - Posts: 710

Joined: November 25, 2003

Location: United States

Posted: May 04, 2004 at 12:34 AM / IP Logged

What are you wiring up? For radios I usually look for an acc spot in the fuse box. Lots of times I find an open one.

djfearny2

Silver - Posts: 810

This member has made a donation to the12volt.com. Click here for more info.

Joined: September 23, 2002

Location: United States

Posted: May 04, 2004 at 1:05 AM / IP Logged

problem with new land rover/cruiser is alot of things are negative.

so for amps your best bet is to connect power to the battery terminalamd and fuse in a good location close to the battery. ground less than 18 inches away from amps or as short as possible. to a clean metal serface and use a wire brush to remove serface of paint. preferable under carpet so if you remote equipment you will not see marking.

also for amps dont run power and rca cables on the same side of the car from front to back this causes engine noise.

Jon

Installer/Help Technician

---coral springs florida---

mecp certification is not always needed. I have it and it has not helped me out at all. my experience out shines it.

palbert

Member - Posts: 4

Joined: May 03, 2004

Location: United States

Posted: May 04, 2004 at 7:26 AM / IP Logged

I am installing a 7" flip down LCD and a DVD player as the entertainment system in a 2003 Rover Discovery. The wiring diagram only states "Red Wire +12V". I know I am suppose to get power from a power source like an open slot in the fuse box, but what if there aren't any open slots? Can I just pig-tail it to the Radio Fuse? Meaning, pull the fuse, insert the wire and compress with the fuse. Any help would be greatly appreciated. Thx.

boomer_106

Silver - Posts: 710

Joined: November 25, 2003

Location: United States

Posted: May 04, 2004 at 10:03 AM / IP Logged

I have done that before with no problems but, I always try to find an open spot in the fuse box. Most of the time when doing a radio you can just use what the factory already provided. If you need a constant 12 volts then you dont wanna use the radio fuse. Usually red is switched but all you say it says is +12 volts so you may wanna doublecheck.

jaurora

Silver - Posts: 429

Joined: January 16, 2004

Location: United States

Posted: May 11, 2004 at 2:05 PM / IP Logged

In that situation you may over draw on current. Run a wire from the battery and be sure to fuse it at least 6" from the battery. If the DVD player is trying to draw more than the spot in the fuse block can handle the wires can get very hot and eventually catch on fire causing some damage. Trust me customers brought there vehicle to me before for this reason. They tried doing it themselves to save a little money but it costed alot more at the end.

MECP certified (If it really means anything)

Jeremy

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Wiring power to LandRover Dscy

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.