Wiring Diagram/Information for 2001 Toyota RAV4

Home / the12volt's Install Bay / General Discussion / Wiring Diagram/Information for 2001 Toyota RAV4 (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

Monkey Racer

Member - Posts: 8

Joined: September 08, 2002

Location: Canada

Posted: September 08, 2002 at 1:35 PM / IP Logged

Need help. Tried looking everywhere for detailed information about the wiring in the 2001 rav4 for stereo/alarm installation. If you have any information that would be useful it would me greatly appreciated.

Thank you.

DeathsJester12V

Silver - Posts: 352

Joined: July 22, 2002

Location: United States

Posted: September 08, 2002 at 2:43 PM / IP Logged

here ya go:

YEAR: 2001 MAKE: Toyota MODEL: RAV4 STYLE:

| 12V |white & BLACK/ red | + |ignition harness |

| STARTER |red | + |ignition harness |

| DOOR TRIGGER |*2 | - |*2 |

NOTES:

NOTE: Some models have an immobilizer system that needs to be bypassed

during remote start. Use DEI module 555F or 555U to bypass.

*1 Unlock requires a double pulse.

*2 The door trigger wires are at the passenger side junction box behind

the glove box. The driver door trigger is RED / yellow in a 10 pin plug in

pin 3, the front passenger door is RED / white in a 20 pin plug in pin 5, and

the rear doors and hatch is RED / white in a 10 pin plug in pin 2.

*3 The data link connector is below the driver side fusebox. The tach wire

is the black wire in pin 9.

Goodluck on the install bub,

Jester

Đễẳ†ђş 12\/ Ĵęśŧē®™

Monkey Racer

Member - Posts: 8

Joined: September 08, 2002

Location: Canada

Posted: September 08, 2002 at 7:31 PM / IP Logged

thank you very much :-)

this will save us some time. We are freezing are butts off out in the rain.

Monkey Racer

Member - Posts: 8

Joined: September 08, 2002

Location: Canada

Posted: September 09, 2002 at 8:30 AM / IP Logged

Ok, another quick question... I notice that you have only one wire for the unlock. I assume that is the unlock sognal from the unlock switches on the door?

Since the rav4 we aree working on has the keyless remote entry fromt he factory it is already hooked up for priority unlock and we would like to interface the new alarm to use priority unlock.

So my question is ... does the same wire you mentioned above control the unlock (i.e. 1 pulse opens driver door and 2nd pulse opens the rest of the doors?) or is that a double pulse just to open all doors and the priority unlock signals fromt he factory wireless module are 2 different wires? ny info you might have would be much appreciated thanks.

aussie

Member - Posts: 5

Joined: August 12, 2002

Location: Australia

Posted: September 10, 2002 at 3:53 AM / IP Logged

To all the fitter in usa do you have problems when you fit a alarm to a car that all ready has remote keyless entry (receiver for keyless ) by fitting a alarm that makes 2 receivers can cause range problems and remotes droping out of program solution is to fit upgrade alarm piggy backs off keyless entry module ( www.dynamco.com.au) this is a universal upgrade hope this is of help aussie

aussie-tech

Monkey Racer

Member - Posts: 8

Joined: September 08, 2002

Location: Canada

Posted: September 10, 2002 at 9:09 AM / IP Logged

Just a note about the "double pulse" for uloock. We simply pulled the lock/unlock wires as labeled by DeathsJester12V and found that a single pull to ground for a fraction of a second worked just fine to lock/unlock the doors... but unfortunately it locks/unlocks all the doors at the same time. We found wires that appear to be the motor control outputs (large gauge) from the drivers side module that control the individual sections of the car (blue/orange 2dots ; blue/orange 1dot ; blue/white 2 dot to lock the doors) (?? drivers unlock) (blue/brown 2dot ; blue 2 dot passenger/hatch unlock). We tested by probing ALL the leads under the drivers side while pressing the buttons on the remote (lock/driver unlock/passenger unlock) and these were the only ones we found to have any apparent signal out. Now if I am correct in assuming the relays are built into the module then there is no externally acessible input to the relays to control from the alarm and since taping these motor control wires directly (using extra relays) would not be an option... our only recourse is to unlock all the doors simultaneously using the wires previously mentioned OR cutting the motor control wires from the module and wiring up our own relay control but eliminating the ability of the factory systems to lock/unlock the doors.

Anyone have any other ideas/info that might help... it would be greatly appreciated. Thank you

Darren

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Wiring Diagram/Information for 2001 Toyota RAV4

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.