96 accord door lock problem

Home / the12volt's Install Bay / Car Security and Convenience / 96 accord door lock problem (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

alexcvn

Member - Posts: 9

Joined: August 01, 2004

Posted: August 11, 2004 at 10:01 AM / IP Logged

Hi, I'm trying to get the power door lock/unlock to work with the alarm's remote, but didn't happen. I uploaded a picture of the diagram, please follow link below to take a look. There are 4 choices of wiring to follow on the diag. , the 1st and 3rd one which I think are for my power door. Right now i'm on the 3rd one that I boxed. I'm pretty sure I followed the correct wiring. Green wire is "up" so I connected it to the orange unlock wire, and Blue wire is "down" so I connected it to the BLACK/ white lock wire. On the diag. says "Motor" ,does that mean the "door lock control unit" which I found on my driver's side door. After I connected all the wires, if i manually use the control switch then it will work but if i use the alarm's lock/unlock remote then nothing happen. Please, any idea of what I did wrong, let me know. Thanks a lot.

http://www.geocities.com/tieuphithu/alphaguards.jpg

raydawg357

Silver - Posts: 769

Joined: June 17, 2003

Location: United States

Posted: August 11, 2004 at 11:22 AM / IP Logged

What type of alarm is it? Your vehicle has (-) locks so all you have to do is connect the unlock wire from the alarm to the orange wire and the lock wire to the BLACK/ white wire. Both of these wires are in a gray plug that is taped to a harness above the driver's side kick panel. Make sure your alarm has a negative output for the locks.

Do it right the first time

alexcvn

Member - Posts: 9

Joined: August 01, 2004

Posted: August 11, 2004 at 4:16 PM / IP Logged

Ive tried to hook up the alarm's wires to the lock/unlock door's wires above driver kick panel. It didn't work. It didn't do anything when I press the remote.

alexcvn

Member - Posts: 9

Joined: August 01, 2004

Posted: August 11, 2004 at 5:09 PM / IP Logged

Should I add relays? According to the diag. provided with link above, it doesn't tell me the wires are (-) or (+) output. All it's saying is; green to unlock, and blue to lock. If so, could someone show me how to add relays to get the door lock/unlock remotely. greatly appreciated.

profuse007

Gold - Posts: 2,015

Joined: October 20, 2002

Location: Texas, United States

Posted: August 11, 2004 at 6:28 PM / IP Logged

does ur alarm unit say anything else for the door lock wires?

like NO, NC, common, 85,86,87,87a......?

Houston,TX

"The two most common elements in the universe are H+ and stupidity" (Ellison).

draasch

Gold - Posts: 2,172

Joined: February 07, 2003

Location: Florida, United States

Posted: August 11, 2004 at 11:02 PM / IP Logged

also make sure you use a meter to find the right wires

Good Luck

David

Ace Security

813-376-9778

Tampa

Donate to the 12volt

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

96 accord door lock problem

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.