05 titan window wire colors

Anyone have the wire colors for the window controls for all four windows and possibly the rear window? Thanks, Brandon

audiovox lists:      LF Window Up     GREEN/ RED     (REV)          WINDOW SWITCH IN DRIVERS DOOR           LF Window Dn     GREEN / WHITE     (REV)          WINDOW SWITCH IN DRIVERS DOOR           RF Window Up     BLUE          (REV)          DRIVER DOOR HARNESS IN KICK PANEL           RF Window Dn     GREEN          (REV)          DRIVER DOOR HARNESS IN KICK PANEL           LR Window Up     RED / YELLOW     (REV)          DRIVER DOOR HARNESS IN KICK PANEL           LR Window Dn     RED / BLACK     (REV)          DRIVER DOOR HARNESS IN KICK PANEL           RR Window Up     BLUE          (REV)          DRIVER DOOR HARNESS IN KICK PANEL           RR Window Dn     RED          (REV)          DRIVER DOOR HARNESS IN KICK PANEL

another-kelly wrote: audiovox lists:      LF Window Up     GREEN/ RED     (REV)          WINDOW SWITCH IN DRIVERS DOOR           LF Window Dn     GREEN / WHITE     (REV)          WINDOW SWITCH IN DRIVERS DOOR           RF Window Up     BLUE          (REV)          DRIVER DOOR HARNESS IN KICK PANEL           RF Window Dn     GREEN          (REV)          DRIVER DOOR HARNESS IN KICK PANEL           LR Window Up     RED / YELLOW     (REV)          DRIVER DOOR HARNESS IN KICK PANEL           LR Window Dn     RED / BLACK     (REV)          DRIVER DOOR HARNESS IN KICK PANEL           RR Window Up     BLUE          (REV)          DRIVER DOOR HARNESS IN KICK PANEL           RR Window Dn     RED          (REV)          DRIVER DOOR HARNESS IN KICK PANEL

Well, this is sorta correct. I found these wires: LF up/down to be GREEN/ red and GREEN / WHITE at switch drivers door. LR up/down to be RED / yellow and RED / black at door harness RR up/down to be red and blue at door harness Now, the problem is with the RF window. This window's switch also has a "one-touch" control for the front passenger. This may be the issue. Out of all the wires in the driver door harness, only when I test this one small green wire for a ground, does the window stop operating. So, do I need to run wires into the front passenger door in order to make this window work?

why don't you just use the driver key cylinder wires to do roll up and down.Shaughn Murley

Install Manager, Dealer Services

Visions Electronics

Red Deer, Alberta

extreme1 wrote: why don't you just use the driver key cylinder wires to do roll up and down.

Huh? Elaborate please...

i was jsut about to post the same thing. If you hold a ground on the lock wire, all of the windows should roll up... and if you hold a ground on the unlock wire, the windows should roll down. I do not believe that you have to necessarily go to the key cylinder, but that may be required.Kenny

Owner / Technician

KKD Garage LLC

Albany, NY 12205

offroadzj wrote: i was jsut about to post the same thing. If you hold a ground on the lock wire, all of the windows should roll up... and if you hold a ground on the unlock wire, the windows should roll down. I do not believe that you have to necessarily go to the key cylinder, but that may be required.

Is this similar to using the factory key fob? If so, I can only roll down the front two windows. I'm not able to roll them up and the back two windows don't work either. Also, does doing this allow the windows to vent?

Ok, I have a big problem with the operation of the driver window now. I have the 530T install. Using channel 4, the window rolls down. When I arm the system, the window rolls up. So, it seems to be working for that. But what is really screwed up is the operation from within the truck. I can no longer roll the window down partially. The drivers control has auto windows. The switch had two ways to move the window. Just slightly pressing the switch caused the window to move. Release this pressure and the window stopped. To auto-roll it, I had to push the switch all the way down pass a "click". Then the window moved the full extent. Now, if I just slightly press the switch to move the window it moves the whole way. I cannot just move the window partially and make it stop.

Now another odd occurrence. When I roll the window up using the drivers switch, the drivers window will sometimes reach the top and then just roll back down. wth??