remote start not working

Home / the12volt's Install Bay / Car Security and Convenience / remote start not working (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

paris12

Member - Posts: 6

Joined: January 05, 2008

Location: Iowa, United States

Posted: January 12, 2008 at 1:05 PM / IP Logged

i put in a 160xv viper not working did i miss any thing i put the

antenna

hood switch

break wire

pluged in ribbon wireing

starter,12 volt constant,ignition 1,accessory1 wires did i miss any its for a 95 ranger i just want the remote start to work.

thanks

usabuilt

Copper - Posts: 161

Joined: September 11, 2007

Location: United States

Posted: January 12, 2008 at 1:44 PM / IP Logged

if you hooked up all the wires correctly, the next step would be programming the module, it should explain it in the installation guide.

another-kelly

Silver - Posts: 618

Joined: July 11, 2004

Location: United States

Posted: January 12, 2008 at 10:15 PM / IP Logged

you've got the following wires connected correctly?

Ignition 1 GREEN/ VIOLET (+) IGNITION SWITCH HARNESS

Accessory 1 GRAY / YELLOW (+) IGNITION SWITCH HARNESS

Starter 1 RED / LIGHT BLUE (+) IGNITION SWITCH HARNESS

did you program tach or put the unit on voltage? disconnect the hood pin cometely until you have the remote start working correctly. actually had someone bring theirs in because they just couldn't get the remote start to work. they just never adjusted the hood pin so it was always showing ground.

another-kelly

Silver - Posts: 618

Joined: July 11, 2004

Location: United States

Posted: January 12, 2008 at 10:21 PM / IP Logged

also, did you ground the smaller gauge BLACK/ white wire labeled as Neutral Safety Switch?

paris12

Member - Posts: 6

Joined: January 05, 2008

Location: Iowa, United States

Posted: January 13, 2008 at 4:30 PM / IP Logged

thanks for the help but not working still

primary harness , ground, 12v

heavy gauge, ignition,12v,accessory,starter

h3 hood pin,brake

what other wires do i need to hook up

tedmond

Gold - Posts: 4,610

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: January 06, 2007

Location: Ontario, Canada

Posted: January 13, 2008 at 9:20 PM / IP Logged

does it give any parkinglight flashes? if so look under diagnostics and see what it shows as error.

speed of sound

Member - Posts: 19

Joined: February 18, 2007

Location: Connecticut, United States

Posted: January 13, 2008 at 9:52 PM / IP Logged

make sure the remotes even respond to the unit. If not program them. Then disconnect the shut down wires ( brake & hoodpin). Make sure you have ground on BLACK/ white wire & black wire and 12 volt on all red wires.

Speed of Sound Technologies

230 pershing Dr

Ansonia, CT 06401

203-954-0066

Search for other posts by speed of sound

another-kelly

Silver - Posts: 618

Joined: July 11, 2004

Location: United States

Posted: January 13, 2008 at 10:31 PM / IP Logged

another-kelly wrote:

also, did you ground the smaller gauge BLACK/ white wire labeled as Neutral Safety Switch?

it's in the small harness with tach, hood pin, brake, and 2nd status

paris12

Member - Posts: 6

Joined: January 05, 2008

Location: Iowa, United States

Posted: January 17, 2008 at 11:32 AM / IP Logged

ok guys thanks for the help got the WHITE/ black wire hooked up now the remote start cranks and seems to want start but does not it does it three times but does not start and when i start it with the key the unit clicks over and over now what do i need to do

Velocity Motors

Moderator - Posts: 12,488

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: January 17, 2008 at 11:49 AM / IP Logged

Where did you ground the unit ? Sounds like a ground issue

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.