viper 5900, 07 ram

Home / the12volt's Install Bay / Car Security and Convenience / viper 5900, 07 ram (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

theminivan

Member - Posts: 7

Joined: April 13, 2008

Location: Louisiana, United States

Posted: September 21, 2008 at 6:35 AM / IP Logged

Alright guys I am wiring a 07 ram with reote start i have a 451m for the doorlocks I've found the purple and dark green wire in kick aneli have the relays wired up and i have the resistors ready i hooked both 330 and820 resistors wired to 2 relays i have constant on 85 both relays 87'sgrounded both 30sgoing to the purple and dark green wires with relays tapped in and 86 is going to the 451m green and blue wires andnothing is hapening cananyone help??like im not getting anything when i hit the unlock nor lock

Is there a better way of wiring this?

Also does anyone have a remote start diagram for a 07 ram?

Yah, I got a project.

i am an idiot

Platinum - Posts: 13,674

This member consistently provides reliable information

Joined: September 21, 2006

Location: Louisiana, United States

Posted: September 21, 2008 at 7:22 AM / IP Logged

How did you connect the resistors in the circuit?

theminivan

Member - Posts: 7

Joined: April 13, 2008

Location: Louisiana, United States

Posted: September 21, 2008 at 8:04 AM / IP Logged

bud connectors.

Yah, I got a project.

chriswallace187

Gold - Posts: 1,661

Joined: March 11, 2002

Location: Pennsylvania, United States

Posted: September 21, 2008 at 1:46 PM / IP Logged

I think the question was "Where are the resistors in relation to the wires from the relays you mentioned?"

They should be inline on wires 30 from the relays to the violet/dk. green on the truck.

'07 Ram has been posted - check the Vehicle Wiring section.

C Renner's Auto Electronix

My service is cheap, quick, and good - pick any two

Search for other posts by chriswallace187

howie ll

Pot Metal - Posts: 16,466

Joined: January 09, 2007

Location: United Kingdom

Posted: September 21, 2008 at 4:16 PM / IP Logged

Bud connector sounds very gay, real men use solder. Have you checked the lock switch to verify the resistance values?

howie ll

Pot Metal - Posts: 16,466

Joined: January 09, 2007

Location: United Kingdom

Posted: September 21, 2008 at 4:21 PM / IP Logged

Sorry, bad attempt at humour but if you've used anything less than 1 watt resistor, apart from the bad electrical connection, it's going to fall out of a butt conector. WHITE/ black, BROWN / black not used, purple and purple black to a GOOD ground preferably an existing bodywork ground point, green /black with lock resistor inline , joined to blue/black with unlock resistor in line, join after resistors to factory lock wire.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

viper 5900, 07 ram

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.