the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

562t remote starter does not crank


Post ReplyPost New Topic
< Prev Topic Next Topic >
mike10_07 
Member - Posts: 11
Member spacespace
Joined: October 24, 2008
Location: California, United States
Posted: October 24, 2008 at 2:03 PM / IP Logged  

I have 562t remote starter and installed to my 2003 camy but my vehicle starter does not crank when I push start button on my remote key. Also when using remote doors can lock only, unlock button can not unlock doors.  My connections are followling ( I don't know it is right since this is my first time) if any one can hlep me please.

  PRIMARY HARNESS (H1):

- RED / white (-) 200mA channel2 Output: to trunk wire with relay( this worked).

- Black Ground Input: to chassis ground.

- White (+/-)Parking light output: directly to Green wire (+) of 2003 camry. ( this worked).

- WHITE/ Blue(-) activation Output and Blue (-) 2nd unlock Ouput: these wires I dont know , WHITE/ Blue wire confused me with Gray(-) Hoodpin Shutdown Input from Remote Harness H3/4.

The Orange (armed), BLACK/ white( domelight), Brown( horn), Green and Violet are not used since I don't need these.

Auxiliary Harness ( H2): not used

 Remote Harnesss(H3):

- Brown (+) Brake Shutdown: to brake wire of vehicle

- BLACK/ White neutral safety Input: one end to toggle switch, the other end to ground.

-  Blue/White 2nd status/defogger: not connected yet

- Gray (-) hoodpin shutdown: connected

- Violet/White Tach input: not connected yet ( dont know if remote starter cannot crank because of not connecting this wire? ).

Door Lock H4:

 - Blue and Green are connected to (-)Blue and (-)Blue / YELLOW in vehicle

This can only lock doors, but cannot unlock doors. I don't know why.

  Relay satellite Wiring:

  - Blue (status), Orange (ACC), Violet (starter output) and Pink(3rd ignition): not used

- Heavy Guage Wires:    -  Purple to the starter side.

                                    -  Green to the key side

                                    - Orange : not connected yet

                                    - Pink to ignition of vehicle

                                    - Pink/White to 2nd ignition of vehicle

                                   -  All 12v Constant Input are connected

I  wonder if I need to connect the second starter wire and How ?

My remote button cannot unlock doors and cannot start ( even the lights are on and off just like igntion on and off when I hit the start button). Please help me

Thanks

 

 

ckeeler 
Gold - Posts: 1,461
Gold spacespace
Joined: June 20, 2008
Location: New Mexico, United States
Posted: October 24, 2008 at 2:45 PM / IP Logged  
In order to start you must power the second starter wire in this vehicle. to unlock the doors you need to program the module for double pulse on unlock. 562t remote starter does not crank -- posted image.
mike10_07 
Member - Posts: 11
Member spacespace
Joined: October 24, 2008
Location: California, United States
Posted: October 24, 2008 at 2:55 PM / IP Logged  

how can I connect the second starter wire?

I think (but not sure) the module is already in double pulse for unlock because the Green wire reads around 14V twice when I hit the unlock button on the remote.

Please help

thanks

ckeeler 
Gold - Posts: 1,461
Gold spacespace
Joined: June 20, 2008
Location: New Mexico, United States
Posted: October 24, 2008 at 3:59 PM / IP Logged  

double, double check that, because it sure sounds like your not set for a double pulse. either that or you have the wrong wire. the 562T has a wire that is a negative pulse start. using a relay connect that wire to term 86, connect term 85 to 12v constant, connect term 30 to 12v constant, connect term 87 to your second starter wire.

xeplep 
Member - Posts: 10
Member spacespace
Joined: October 13, 2008
Location: Oregon, United States
Posted: October 24, 2008 at 10:52 PM / IP Logged  

Thanks for your help Ckeeler, i will check the doors again. However, instead of a negative pulse start for connecting to second starter wire ( using relay as you recommended) the Violet (starter output) from 562t come out with 14V. This make me confused and then I disconnected other wires connecting to the Relay satellite, just connect the 12v constant input to it . The signal of Violet ( starter ouput) still 14V .

I dont know why ?????

mike10_07 
Member - Posts: 11
Member spacespace
Joined: October 24, 2008
Location: California, United States
Posted: October 26, 2008 at 11:56 PM / IP Logged  

Thanks Ckeeler, Finnaly my RS works but only with the key in the Ignition. Does My 2003 camry needs a transponder module for RS to work ?. what kind of transponder do you suggest ?.

DEI 556U  is good for my 2003 camry ?

thanks .

ckeeler 
Gold - Posts: 1,461
Gold spacespace
Joined: June 20, 2008
Location: New Mexico, United States
Posted: October 27, 2008 at 8:55 AM / IP Logged  
the 556U will work. i like the ones though that dont require an extra key.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, March 28, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer