problem autopage rs1000

Home / the12volt's Install Bay / Car Security and Convenience / problem autopage rs1000 (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

skostur79

Member - Posts: 19

Joined: August 29, 2006

Posted: November 22, 2008 at 11:40 AM / IP Logged

can anyone with autopage experience

help me out ,

i just installed a rs1000 2 way , tested , learn rpms all good all functions work,

the next day i got nothing from transmitter 1 or 2 ,

turning the ign , the locks cycle like the should ,

i dropped the module down checked all connections , powers ,grounds good

i can enter programing mode but since it dont pick up the transmitter , it exits,

so how can i diagnose a bad transmitter or bad module?

i dont think autopage will help me with warrentys

thanks

p01110101

Member - Posts: 43

Joined: January 12, 2004

Posted: November 22, 2008 at 12:08 PM / IP Logged

try re-learning the remotes, your manual should tell you how to do it.

skostur79

Member - Posts: 19

Joined: August 29, 2006

Posted: November 22, 2008 at 12:16 PM / IP Logged

ya i tryed that

i get the step (press any key on the fob ) but no chirp

the 15 sec it times out

any more suggestions , thanks

lamikela1

Member - Posts: 22

Joined: October 26, 2006

Location: United States

Posted: November 25, 2008 at 4:05 PM / IP Logged

If you tried both remotes and no luck then I would suspect that the antenna or module is bad as both remotes can't be bad. If you know someone who has another RS-1000 try to program your remotes on that system to see if they work. If you can find a shop that installs them they may have a test system that you can try them on.

Pioneer AVIC-Z1, JL 8W3V2, XR650CSi, 300/4, 250/1, Bluetooth, XM, A/V switch, Backup Cam, Autopage RS-1000

skostur79

Member - Posts: 19

Joined: August 29, 2006

Posted: November 25, 2008 at 6:51 PM / IP Logged

ya im bummed because i just installed it ,

the local autopage shop wont look at it unless they installed it,

, but they will sell me a new one for 650..00

i called autopage ,they will check it out,

but 2 plus weeks to get it there and repaired ,

i sent it off

ceasar326

Copper - Posts: 239

This member has made a donation to the12volt.com. Click here for more info.

Joined: February 02, 2006

Location: Minnesota, United States

Posted: November 25, 2008 at 9:33 PM / IP Logged

Have u checked the ground point make sure its a good ground ive dealed with autopage alot. Ground points are your best bet.

skostur79

Member - Posts: 19

Joined: August 29, 2006

Posted: November 25, 2008 at 9:59 PM / IP Logged

Ya grounded at dash crosscar bar .2 ohms

I can ground the h10/18 wire and it will remote start ok

Thanks I'll post the findings once I get it back

skostur79

Member - Posts: 19

Joined: August 29, 2006

Posted: December 30, 2008 at 7:54 PM / IP Logged

well finally after about a month

autopage sent the repaired unit,

no faults in the remotes , replaced the main control module

so far it works maybe i can make into winter with it now ,,,

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

problem autopage rs1000

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.