Hi, it's a first time when i am trying to install car alarm into my car.
Car: toyota celica 2004 GT (USA made)
Alarm: Viper 5002
First i started with wiring info collecting and making such a list or smth. where i should connect every wire. Could anyone help me with it. Car alarms are quite new for me so i don't want that after wiring everything would blow up :)
viper install manual
Toyota celica wiring info
My wiring:
Primary Harness (H1) 12 Pin
H1/1 RED / White (-) 200mA Channel 2 output (trunk release) >> Trunk/Hatch Pin / lt. Green / - / trunk light or BCM (or Trunk/Hatch Release, where it is?)
H1/2 Red (+) Constant 12V Power Input (15A fused) >> 12volts / BLACK/ red and white / + / ignition harness
H1/3 Brown (+) siren output >> siren red wire
H1/4 Yellow (+) switched Ignition Input, Zone 5 >> Ignition / BLACK/ orange / (+) / ignition harness
H1/5 Black (-) Chassis ground Input >> to the ground (paint free sheet metal location)
H1/6 Violet (+) Door trigger input, Zone 3 >> leave disconnected ???
H1/7 Blue (-) Instant trigger Input (trunk input/shunt), Zone 1 >> Trunk/Hatch Pin / lt. Green / - / trunk light or BCM (not sure!)
H1/8 Green (-) door trigger input, Zone 3 >> door trigger / RED / white / (-) / driver kick panel
H1/9 BLACK/ white Domelight Supervision Relay Output #30 >> dome supervision / use door trigger
H1/10 WHITE/ blue (-) 200mA Channel 3 programmable Output >> ??
H1/11 White (+)/(-) selectable light flash output >> parking lights / lt. Green / (-) / steering column (set jumper to negative)
H1/12 Orange (-) 500mA Ground-When-Armed Output >> ???
Auxiliary Harness (H2) 8 Pin
H2/1 Light Blue (-) Second Unlock >> ??
H2/2 Grey (-) Hood Pin Input, Zone 6 >> ??
H2/3 ORANGE / Black Retained Accessory Output >> accessory / gray / (+) / ignition harness (not sure!)
H2/4 Grey/Black (-) Channel 6 Output 200mA >> ??
H2/5 WHITE/ Black (-) Channel 5 Output 200mA >>??
H2/6 Violet/Black (-) Channel 4 Output 200mA >> ??
H2/7 Light Brown (-) Horn Honk Output 200mA >> horn trigger / blue/black / (-) steering column or BCM
H2/8 Light GREEN/ Black (-) Factory Disarm Output >> disarm defeat / blue/red / 5wi / passenger kick or BCM (not sure!)
Door Lock Harness 7 Pin
H3/A BLACK/ White Domelight Supervision relay Input #87 >> to the chassis ground (door pin circuit negative)
H3/B - H3/G Type B - Three wire (-) ground pulse controlling factory lock relays (i think)
H3/B WHITE/ Black Lock #87 Normally Closed >> Not Used
H3/C GREEN/ Black Lock #30 Common (output) >> power lock / brown / (-) / passenger kick or BCM
H3/D Violet/Black Lock #87 Normally Open (Input) >> to chassis ground w/ violet wire
H3/E BROWN / black Unlock #87 Normally Closed >> not used
H3/F Blue/Black Unlock #30 Common (output) >> power unlock / yellow/black / (-) passenger kick or BCM
H3/G Violet Unlock #87 Normally Open (input) >> to chassis ground w/ violet/black wire
Immobilizer Wire Connection 3 Pin
A GREEN/ Black Starter - Normally Closed (motor side) >> starter / BLACK/ white / (+) / ignition harness (to the starter circuit)
B Green Starter Normally Open (motor side) >> not used
C GREEN / WHITE Starter Common (key side) >> starter / BLACK/ white / (+) / ignition harness (to ignition switch)
Also, i have one
wire witch was in box but i don't know where to use it.
Will i need any other components (diodes etc.)? Where?
Thank You for any help.