viper 5901, toyota tacoma

2008 Toyota Tacoma. Several people have said I would need to use diodes when using the viper 5901 on door lock wires, the dome light wires (some even say a relay here) and on the keysense wire(goes to the module and the Fortin bypass). Other tell of their install and do not mention using any diodes, just a relay for the 2nd start. Anybody know the correct way?

TACOMA       2005 -2009     PART       COLOR       LOCATION       DIAGRAM 12 VOLT CONSTANT       WHITE/ BLUE (+) and WHITE/ RED (+)       IGNITION SWITCH HARNESS       STARTER       GREEN/ BLACK (+) See NOTE *1       IGNITION SWITCH HARNESS       STARTER 2       BLACK/ WHITE (+) See NOTE *1       IGNITION SWITCH HARNESS       IGNITION 1       BLACK/ RED (+)       IGNITION SWITCH HARNESS       IGNITION 2       BLUE / YELLOW (+)       IGNITION SWITCH HARNESS       IGNITION 3       N/A             ACCESSORY /HEATER BLOWER 1       WHITE/ GREEN (+)       IGNITION SWITCH HARNESS       ACCESSORY /HEATER BLOWER 2       N/A             KEYSENSE       GREEN/ BLACK (-)       IGNITION SWITCH HARNESS       PARKING LIGHTS ( - )       GREEN (-)       @ HEADLIGHT SWITCH or BCEU, PIN 13, See NOTE *2       PARKING LIGHTS ( + )       GREEN (+)       @ FUSE BOX 13-Pin plug, Pin 10       POWER LOCK       PURPLE (TYPE B) See NOTE *3       IN DRIVERS KICK PANEL, 10-Pin plug, Pin 4       POWER UNLOCK       GREEN/ BLACK (TYPE B) (Requires Double Pulse)       IN DRIVERS KICK PANEL, 10-Pin plug, Pin 8       LOCK MOTOR WIRE       BLUE/RED (+)       IN DRIVERS KICK PANEL, 12-PIN Plug, Pin 10       DOOR TRIGGER       See NOTE *4       @ FUSE BOX       14301_TACOMA_(-) NEGATIVE DOOR PIN ISOLATION CIRCUIT.pdf DOMELIGHT SUPERVISION       BLUE (-), Requires Part #775 Relay       @ FUSE BOX, BLACK 13-Pin plug, pin 9       TRUNK RELEASE       N/A             SLIDING POWER DOOR       N/A             HORN       GREEN/ RED (-)       @ FUSE BOX, 18-PIN Plug, Pin 10       TACH       BLACK/ WHITE       @ DATA LINK CONNECTOR,pin 9, See NOTE *5       WAIT TO START LIGHT       N/A             BRAKE       BLUE (+)       @ FUSE BOX, 11-PIN Plug, Pin 2       FACTORY ALARM DISARM       DISARMS with KEYSENSE wire, See NOTE *6       @ IGNITION SWITCH HARNESS       ANTI-THEFT       TRANSPONDER ANTI-THEFT SYSTEM, REQUIRES 791 BYPASS MODULE AND EXTRA IGNITION KEY See NOTE *7       TRANSPONDER @ IGNITION SWITCH TUMBLERBig Al

This is the wiring list I have seen posted here, but it says see note 1,2,3,4,5,6,7, but I never see the notes posted. Thanks

OTE *1 this vehicle uses (2) STARTER/CRANK wires, when connecting to a Remote Starter you must connect BOTH STARTER/CRANK wires to the STARTER/CRANK wire from the Remote Starter. NOTE *2 the BECU (Body Electronic Control Unit) is attached to the back of the FUSE BOX, with a single 26-Pin Plug. NOTE *3 when testing the DOOR LOCK and UNLOCK wires, you must TEST these wires when turning the kEY in the DRIVERS DOOR KEY CYLINDER ONLY. NOTE *4 the DRIVERS DOOR is a GREEN/ YELLOW (-) in the 18-pin plug, pin 7, the PASSENGER DOOR is a RED / BLACK (-) in a 22-pin plug, pin 8, the REAR DOORS are a PINK/BLACK (-) in an 18-pin plug pin 6, when connecting to an ALARM SYSTEM, use all (3) DOOR TRIGGER wires and DIODE ISOLATE, to connect, See DIAGRAM NOTE *5 the DATA LINK CONNECTOR is located under the DRIVERS SIDE of the DASH. NOTE *6 THE KEYSENSE WIRE WILL DISARM THE VEHICLE WITHOUT UNLOCKING THE DOORS BY APPLYING A (-)NEGATIVE TO THIS WIRE DURING REMOTE STARTING. NOTE *7 the TRANSPONDER ANTI-THEFT System is standard on all V-6 models.Big Al

See how I installed this on my 2005 Tacoma: http://www.toyotanation.com/forum/showthread.php?p=2991492#post2991492 http://www.toyotanation.com/forum/showthread.php?p=2991492#post2991492 Always test. When in doubt, read and study. If still in doubt, read some more. If that don't work, don't do it then or your burn everything... a Chef