cs remote starter keeps cranking

Home / the12volt's Install Bay / Car Security and Convenience / cs remote starter keeps cranking (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Page < Prev Topic Next Topic >

moonliter

Copper - Posts: 322

Joined: February 28, 2007

Location: Canada

Posted: February 10, 2010 at 8:06 PM / IP Logged

coreythiessen wrote:

I can start the truck and press the remote starter button and take the key out.

Do you mean tthe truck kept running with the key removed ?

Back to Top

coreythiessen

Member - Posts: 9

Joined: February 10, 2010

Location: Saskatchewan, Canada

Posted: February 10, 2010 at 8:09 PM / IP Logged

Yes, that's correct.

Back to Top

moonliter

Copper - Posts: 322

Joined: February 28, 2007

Location: Canada

Posted: February 10, 2010 at 8:16 PM / IP Logged

hmmm....Now what can it be ? You had tach signal but could be NOT properly set. The take over test proved it. May be change the cylinder setting higher or lower. At the moment it could be over cranked. I m not sure which way it should go. only way to find out is to try I guess.

Back to Top

coreythiessen

Member - Posts: 9

Joined: February 10, 2010

Location: Saskatchewan, Canada

Posted: February 10, 2010 at 8:20 PM / IP Logged

I guess that's where the other problem comes in. When I went through the 9 step programming, nothing changes. I tried the 8 cyl and the low setting. I did notice that it will accept settings up to 11 steps. Are there instructions for a 11 step unit?

Back to Top

moonliter

Copper - Posts: 322

Joined: February 28, 2007

Location: Canada

Posted: February 10, 2010 at 8:25 PM / IP Logged

are you sure this is 270ic ? It could be a 290ic ( it comes with a two button remote)

use this for reference the last 4 steps are for cylinder selection

https://www.the12volt.com/installbay/file.asp?ID=307

Back to Top

coreythiessen

Member - Posts: 9

Joined: February 10, 2010

Location: Saskatchewan, Canada

Posted: February 10, 2010 at 8:48 PM / IP Logged

The unit looks like the picture on the 310 wiring instructions.

I tried the ones you linked, I tried the 310, and the 290. None seem to make any difference.

Back to Top

kgerry

Platinum - Posts: 3,455

This member consistently provides reliable information

Joined: February 07, 2004

Location: Saskatchewan, Canada

Posted: February 11, 2010 at 9:03 AM / IP Logged

thats what i love about DEI units... start car, press a button, LED comes on, Tach learned, DONE!

can you program the unit to voltage sense just to try and eliminate a tach issue (sure sounds like a tach issue)

Kevin Gerry

Certified Electronics Technician

MECP First Class Installer

Owner/Installer

Classic Car Audio

since 1979

Back to Top

< Prev Page

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

cs remote starter keeps cranking

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.