96 eclipse viper 5901 remote start error

Home / the12volt's Install Bay / Car Security and Convenience / 96 eclipse viper 5901 remote start error (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Page < Prev Topic Next Topic >

freakingbori617

Member - Posts: 6

Joined: May 22, 2010

Location: Massachusetts, United States

Posted: May 23, 2010 at 8:15 AM / IP Logged

yes the door pin is connected. And the tach wire is connected and used the control center to program tach. I had the starter input and output backwards so i fixed that. But now once i start my car with my key the starter wont disengage.So the remote start wiring must be wrong on something i just cant figure it out

Back to Top

Search for other posts by freakingbori617

smokeman1

Platinum - Posts: 1,588

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: September 14, 2009

Location: Wisconsin, United States

Posted: May 23, 2010 at 8:42 AM / IP Logged

Looking back on your first post, it looks like you might have the H3/3 wire and the H3/7 wire reversed. The wiriing charts list the BLUE/BLACK as Accessory, and the BLUE as Ignition 2. Also do you have the H3/7 programed as Ignition 2?

H3/7 PINK/WHITE – Ignition 2 flex relay output.

This wire is factory programmed as Ignition 2 and can be programmed as a 2nd

accessory or 2nd starter.

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

Back to Top

dasbogie

Silver - Posts: 514

Joined: September 30, 2006

Location: Pennsylvania, United States

Posted: May 23, 2010 at 3:14 PM / IP Logged

since this is a manual how did you bypass the clutch? does it need to be pressed to the floor to start the vehicle with the key?

Advanced

Back to Top

freakingbori617

Member - Posts: 6

Joined: May 22, 2010

Location: Massachusetts, United States

Posted: May 23, 2010 at 4:41 PM / IP Logged

That wiring diagram is wrong the blue wire is acc and the blue black is the 2nd ignition. I have checked myself.I corrected the battery drain it had nothing to do with the install.

I removed the clutch switch completely so i can start the veichle without pressing the clutch pedal. Im really fustrated i have check my wiring atleast 6 times and im sure its correct. Is there a way to switch it to automatic mode instead of manual?

Back to Top

t&t tech

Platinum - Posts: 2,608

Joined: October 05, 2008

Location: Trinidad and Tobago

Posted: May 23, 2010 at 7:03 PM / IP Logged

Yes! But we cannot tell you how! t's against fourum rules! Do it by the book!

commit your way to jehovah and he will act in your behalf. psalms 37:5

Back to Top

< Prev Page

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

96 eclipse viper 5901 remote start error

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.