2010 honda insight wiring diagram

Hello fellow comrades, I could sure use a diagram for an alarm/remote start system if you have access to it. I greatly appreciate the assistance! Nate

HONDA MODEL      YEAR(S) INSIGHT      2010 - KEY      T-HARNESS      IMMOBILIZER N/A      N/A      HONDA'S TRANSPONDER SYSTEM, Requires Bypass Module, See NOTE #1 PART       COLOR      LOCATION 12 VOLT CONSTANT      WHITE (+) 50 AMP      @ IGNITION SWITCH, (BROWN, 7-Pin Plug) Pin 3 STARTER      RED (+)      @ IGNITION SWITCH, (BROWN, 7-Pin Plug) Pin 1 STARTER 2      N/A      IGNITION 1      YELLOW (+)      @ IGNITION SWITCH, (BROWN, 7-Pin Plug) Pin 6 IGNITION 2      N/A      IGNITION 3      N/A      ACCESSORY /HEATER BLOWER 1      ORANGE (+)      @ IGNITION SWITCH, (BROWN, 7-Pin Plug) Pin 4 ACCESSORY /HEATER BLOWER 2      RED (+)      @ IGNITION SWITCH, (BROWN, 7-Pin Plug) Pin 5 KEYSENSE      N/A      PARKING LIGHTS ( - )      GRAY (-)      @ HEADLIGHT SWITCH, (BLACK/ WHITE, 12-Pin Plug) Pin 11 PARKING LIGHTS ( + )      GRAY (+)      @ DASH FUSE BOX, (LT. GREEN / WHITE, 49-Pin Plug) Pin 42 POWER LOCK      GREEN (-) TYPE B      @ DASH FUSE BOX, (LT. GREEN, 12-Pin Plug) Pin 8 POWER UNLOCK      WHITE (-) TYPE B      @ DASH FUSE BOX, (LT. GREEN, 12-Pin Plug) Pin 1 DOOR TRIGGER      GRAY (-)      @ DASH FUSE BOX, (LT. GREEN / WHITE, 49-Pin Plug) Pin 33 DOMELIGHT SUPERVISION      BLUE -)      @ DASH FUSE BOX, (LT. GREEN, 8-Pin Plug) Pin 7 TRUNK RELEASE      PINK (-)      @ DASH FUSE BOX, (LT. GREEN / WHITE, 49-Pin Plug) Pin 17 SLIDING POWER DOOR      N/A      HORN      ORANGE (-)      @ HORN SWITCH, (WHITE, 20-Pin Plug) Pin 1 TACH      N/A      WAIT TO START LIGHT      N/A      BRAKE      WHITE to LT. GREEN (+)      @ BRAKE SWITCH or DASH FUSE BOX, (LT. GREEN / WHITE, 49-Pin Plug) Pin 14 FACTORY ALARM DISARM      GRAY (-) NOTE #2      @ DASH FUSE BOX, (LT. GREEN, 12-Pin Plug) Pin 4 ANTI-THEFT      HONDA'S TRANSPONDER SYSTEM, Requires Bypass Module, See NOTE #1      EXTRA INFORMATION NOTE #1: HONDA'S TRANSPONDER SYSTEM, Requires Bypass Module, Part # PKALL NOTE #2: TEST this wire while turning the Key in the Drivers Door.

You rock dude~!  Expeditious reply...... Couldn't ask for more!Nate Dizzle

how do i find out the number for each pin? for example: the harness has 49pin connector, so which one is pin number 1, number 2, 3,.... etc.

Thanks of helping.

STARTER      RED (+)      @ IGNITION SWITCH, (BROWN, 7-Pin Plug) Pin 1 STARTER 2      N/A       IGNITION 1      YELLOW (+)      @ IGNITION SWITCH, (BROWN, 7-Pin Plug) Pin 6 Example: Pin1 BROWN is on the edge of the plug. Pin6 BROWN will be NOT on the edge. Therefore where the BROWN is on the edge is PIN 1. Count from there. Better yet. Find the suspected color wire, and using your DMM test the wire.

If it's a Siemens/AMP or Molex get out your magnifying glass, the start and end numbers will be etched on, e.g. 1 and 24, 25 and 49.