the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2002 saturn remote start


Post ReplyPost New Topic
< Prev Topic Next Topic >
buzzstpoint 
Member - Posts: 11
Member spacespace
Joined: December 26, 2010
Location: Wisconsin, United States
Posted: December 26, 2010 at 7:42 PM / IP Logged  
Vehicle:
2002 Saturn L200
4 cylinder
Remote start: Bulldog RS1200
Bypass: Bulldog 791
I wired up the remote start, So far everything seems to work except the starting function.
The car will crank and start only to shut down 1-2 seconds later. I did notice the security light is on when this happens. I've doubled and tripled check the wiring. Trouble shooting says to clear the bypass and "relearn" the resistance. I have done this about 10 times already and still no luck.
I'm wondering if it has to do with the Keysence. According to the instrucions I should add a diode to the (-) out when running on the remote start. But then the Bypass says I should use the same wire.
I put the bypass wire before the diode. should this be after the diode?
Any other ideas why the car would shut down right away when using the remote start is activated?
blanx218 
Silver - Posts: 654
Silver spacespace
Joined: September 23, 2008
Location: Pennsylvania, United States
Posted: December 26, 2010 at 8:34 PM / IP Logged  
did 2 of these cars this week and did not have any luck with any bypass. i had to go old fashioned and use a relay and resistor
buzzstpoint 
Member - Posts: 11
Member spacespace
Joined: December 26, 2010
Location: Wisconsin, United States
Posted: December 26, 2010 at 9:23 PM / IP Logged  
Do you have a schematic of the "resistor and relay" version?
kreg357 
Platinum - Posts: 7,781
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: Pennsylvania, United States
Posted: December 26, 2010 at 9:30 PM / IP Logged  
Passlok2 bypass from Audiovox :  http://documents.audiovox.com/700054.pdf
Soldering is fun!
zerepdivad 
Silver - Posts: 605
Silver spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: July 03, 2006
Location: Wisconsin, United States
Posted: December 26, 2010 at 9:40 PM / IP Logged  
yup. that's the only way i do saturns. they often have oddball resistances apparently i guess is the issue.
A DMM is a beautiful thing.
MECP Advanced Installer Certified.
buzzstpoint 
Member - Posts: 11
Member spacespace
Joined: December 26, 2010
Location: Wisconsin, United States
Posted: December 27, 2010 at 10:52 AM / IP Logged  
What type of relays are these?
SPDT? Amperage?
ayalja123 
Copper - Posts: 64
Copper spacespace
Joined: September 30, 2003
Location: United States
Posted: December 27, 2010 at 1:13 PM / IP Logged  
hey did you try using a pljk? i know that on xpresskit.com the pljk does not come up for this vehicle but i think it might work
blanx218 
Silver - Posts: 654
Silver spacespace
Joined: September 23, 2008
Location: Pennsylvania, United States
Posted: December 27, 2010 at 1:24 PM / IP Logged  
i thought the same thing but the pljx does NOT work. it will program (or appear to program) fine but as soon as you try the r/s it locks up the passlock
ayalja123 
Copper - Posts: 64
Copper spacespace
Joined: September 30, 2003
Location: United States
Posted: December 27, 2010 at 1:43 PM / IP Logged  
ok, good to know, thanks. I've done saturns but not this one
buzzstpoint 
Member - Posts: 11
Member spacespace
Joined: December 26, 2010
Location: Wisconsin, United States
Posted: January 02, 2011 at 5:46 PM / IP Logged  
Here's where I'm at.
I've wired up the Passlock according to the "audiovox" bypass instructions.
I now have a couple of issues.
When using the key, The security light will be lit but will start and run.
If I run the remote start, push on the brake the engine will shut down. After this, I can't start the engine with the key. I have to start the engine with the remote then use the key. Only after I do this will I be able to use the key.
Lastly, when I hook bypass in, the airbag light is on.
Any ideas on where to go from here?
Page of 2

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer