the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

compustar cm4200 issues


Post ReplyPost New Topic
< Prev Topic Next Topic >
jonathan.tamayo 
Member - Posts: 2
Member spacespace
Joined: April 12, 2011
Location: California, United States
Posted: April 13, 2011 at 1:16 AM / IP Logged  

Hi all, i installed an cm4200 in my 90 crx(manual tranny). the issue i am having is with the horn output no honk(use a relay every way you possibly can to get to work but nothing), also my door trigger is not setting the brain off when i open the door when car is armed and last the remote start is not cranking everything work light flash dash lights come on fuel pump evrything but no crank and if i am inside the car and remote start it with my foot down on the car fires right up, now the reason i purchased a compustar unit is because i thought u wouldnt have 2 bypass the clutch, i even tryed hooking up the lutch wire to the - status wire from cn2 i normally purchase dei units but this is my first compustar. i have wiring ass followed

cn1

red-12v-connected to wht in column harness

grn/wht-parking lights-connected to RED / grn kick panel

RED / wht-12v(piggy backed red)

white-acc-yellow column harness

blue-not used

grn/red-ign-blk/ylw column harness

blk-ground

cn2

grn/wht-not used

RED / black-starter output-tried to clutch nothing

violet-output to starter kill-to relay

black-- status output-tryed 2 clutch as well

org-not used

wht-horn output-connected to blu/red  (relayed different ways to get horn to work and nothing

cn3

lt blu- e brake- connected to grn/red-kick panel

gry/blk -not used-hoodpin

lt blu/wht-brake-connected to brake wire @ switch

vio/blk-trunk trigger-not used

RED / wht-(-) door trigger- connected to - grn/red-drivers kick

red-(+) door trigger-not used

brn/blk-glo plug-not used

bwn/wht-glo plug-not used

ylw/blk-tach-connect to blue wire @ dist.

cn3-not used

i have programmed remotes, tach learned and put in reservation mode, all dip switchs and jumpers are correct to book, your help is very appriciated and welcome, thanks and hope to hear from someone, i am thinking my unit is bad....

Damn it
JWorm 
Platinum - Posts: 2,208
Platinum spacespace
Joined: December 11, 2002
Location: New Hampshire, United States
Posted: April 14, 2011 at 11:58 PM / IP Logged  
You are probably connecting the RED / black to the wrong wire at the clutch switch. It should be the wire that goes to ground only when the clutch is between 90-100% of the way to the floor.
For the horn... Have you changed setting 3-8 in programming to option 2?
jonathan.tamayo 
Member - Posts: 2
Member spacespace
Joined: April 12, 2011
Location: California, United States
Posted: April 15, 2011 at 3:45 PM / IP Logged  
ill double check my wiring @ clutch and as far as programming i have not i look in the book for programming option for the horn and there was nothing on it but ill try it and see what happens
thanks
Damn it

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Wednesday, September 28, 2022 • Copyright © 1999-2022 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer